This stair carpet calculator works out how much carpet or runner you need to cover a staircase. Enter the number of steps, the tread depth, the riser height, the width and an allowance for wrapping each nosing, and the stair carpet calculator gives the total carpet length and area in square feet, square yards or square meters.
How to use the stair carpet calculator
- Choose US or metric units. US (inches) is the default.
- Count the steps you'll carpet and enter the tread depth and riser height.
- Enter the carpet width and the nosing wrap for each step.
- Add a landing length or waste allowance if needed, then press Calculate.
Parts of a stair
Wikipedia's article on stairs explains the parts you'll measure. The tread is the part of the step you stand on, and the riser is the vertical part between one tread and the next. The nosing is the edge of the tread that sticks out over the riser below. The number of steps equals the number of risers. Carpet runs over each tread, wraps around the nosing and down the riser.
How the calculator works
Each step uses carpet equal to its tread depth plus its riser height plus the extra that wraps around the nosing. The calculator multiplies that by the number of steps, adds any landing, and adds your waste allowance:
carpet length = steps × (tread + riser + nosing wrap) + landing
The area is the length times the carpet width. For US units, the calculator shows the area in square feet and square yards, since carpet is often sold by the square yard.
Typical step sizes
For houses built to the 2021 International Residential Code, section R311.7.5 limits risers to 7¾ inches and requires treads at least 10 inches deep, with a nosing that projects ¾ to 1¼ inches on most stairs. Your stairs may differ, especially in older houses, so measure a few steps. If they vary slightly, use the largest.
Worked example
A straight stair has 13 steps, each with a 10-inch tread and a 7½-inch riser. Allowing 1 inch to wrap each nosing, each step uses 18.5 inches of carpet. For 13 steps, that's 240.5 inches, about 20 feet ½ inch. With a 36-inch-wide runner, the area is 240.5 × 36 = 8,658 square inches, about 60.1 square feet or 6.68 square yards.
Reading the results
The big number is the length of carpet to cover the stairs. The table shows the area, in square yards for US units, and the carpet used per step.
Runners and full-width carpet
A runner covers the middle of the stairs, leaving some wood showing at each side, so use the runner's width. Full-width carpet covers wall to wall, so measure the full width of the treads. On open-sided stairs, the carpet may also wrap the sides of each tread, which needs extra.
Metric stairs
Choose metric to enter the step sizes and width in millimeters. The calculator shows the length in meters and the area in square meters. A stair of 13 steps with 255 mm treads, 190 mm risers and 25 mm of nosing wrap needs about 6.1 meters of carpet; at 900 mm wide, that's about 5.5 square meters.
Landings
Many stairs have a landing partway up or at the top. Measure the depth of the landing in the direction of travel and enter it as the landing length; the calculator adds it to the carpet length at the same width. For an L-shaped or U-shaped stair, the landing is usually wider than the runner, so you may need to work out its carpet separately as a rectangle.
Allowing for waste
Carpet usually comes from a roll in fixed widths, and fitters may need extra for joins, trimming and matching a pattern from step to step. Add a waste allowance to cover this. The calculator increases both the length and the area by the percentage you enter, so a 10% allowance turns 240.5 inches into about 264.6 inches.
Ordering carpet
Carpet is often priced per square yard or square meter. Multiply the area by the price to estimate the cost, and remember to include underlay and fitting if they're priced separately. Ask your supplier whether they sell runners in set lengths, since a runner can usually be cut to length from a roll of the right width.
Measuring tips
Measure the tread depth from the back of the step to the front edge of the nosing, and the riser height from the top of one tread to the top of the next. Measure a few steps, because they can differ slightly, especially in older homes, and use the largest values so the carpet doesn't come up short.
Common mistakes
- Forgetting the nosing. Carpet must wrap the front edge of each tread.
- Counting the top floor as a step. Count only the steps you'll cover.
- Measuring one step only. Steps can vary, so measure several.
- Ignoring pattern matching. Patterned carpet needs extra.
Tips
- Measure the tread from the back of the step to the front of the nosing.
- Order carpet from the same batch so the color matches.
- Ask your fitter how they'll lay it before you buy.
What next
Use this often? Add Stair Carpet to your Home screen.
Frequently asked questions
How does a stair carpet calculator work?
It adds each step's tread, riser and nosing wrap, multiplies by the number of steps and by the carpet width.
How much carpet do I need for 13 stairs?
With 10-inch treads, 7½-inch risers and a 1-inch nosing wrap, about 20 feet of length.
How do I measure stairs for carpet?
Measure the tread depth, the riser height and the width, and count the steps.
What are typical stair dimensions?
The 2021 IRC limits risers to 7¾ inches and requires treads at least 10 inches deep.
Do I need extra carpet for the nosing?
Yes, enough to wrap around the front edge of each tread.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.