Saved

Press the star next to a tool's name to save it.

All my tools

RMS Voltage Calculator

Use this rms voltage calculator to convert the peak, peak-to-peak or average voltage of a sine, square, triangle, sawtooth or rectified wave to its RMS value, with a DC offset.

Restored your last values ·

V
V

Pick the waveform and the voltage you know (peak, peak-to-peak or average), enter its value and, if the signal sits on a DC level, the offset. You get the RMS voltage.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose the waveform, enter a voltage and press Calculate.

See full result

An rms voltage calculator converts the peak, peak-to-peak or average voltage of a waveform into its root mean square value, the DC-equivalent voltage that would deliver the same power into a resistor. It handles sine, square, triangle, sawtooth and rectified waves, with an optional DC offset.

How to use the rms voltage calculator

  1. Choose the waveform.
  2. Choose which value you know: Vp, Vpp or Vavg, and enter it.
  3. Add the DC offset if the signal has one.
  4. Press Calculate.

What RMS voltage means

The root mean square is the square root of the arithmetic mean of the squares of the values [1]. For an alternating voltage it is the number that heats a resistor as much as the same direct voltage would. That is why mains voltage is quoted as an RMS value: a 230 V supply is not 230 V at its peak but equivalent to a 230 V direct supply in power.

Formulas from the peak

From the peak voltage Vp, the RMS value is Vp ÷ √2 for a sine wave, Vp for a square wave and Vp ÷ √3 for a triangle or a sawtooth wave [1]. For a half-wave rectified sine it is Vp ÷ 2, and for a full-wave rectified sine it is Vp ÷ √2 [2]. All of these follow from the definition of the RMS as the square root of the mean of the squares [1].

From the peak-to-peak voltage

The peak-to-peak value is twice the peak for these symmetric waveforms, so the RMS is Vpp ÷ (2√2) for a sine wave, Vpp ÷ 2 for a square wave and Vpp ÷ (2√3) for a triangle. Wikipedia gives the matching relations, peak-to-peak = 2√2 × RMS for a sine wave and 2√3 × RMS for a triangle wave [1]. The calculator first halves Vpp and then applies the peak factor.

From the average voltage

The average here is the average of the rectified wave. For a full-wave rectified sine the average is 2 Vp ÷ π and the RMS is Vp ÷ √2 [2], so the RMS is π × Vavg ÷ (2√2), which for 6.37 V gives 7.07 V. For a half-wave rectified sine the average is Vp ÷ π and the RMS is Vp ÷ 2 [2], so the RMS is π × Vavg ÷ 2. We left Vavg out for the triangle and sawtooth waves.

Adding a DC offset

If the signal sits on a DC level V₀, the RMS value is the square root of V₀² plus the AC RMS squared. Wikipedia describes V_DC as the direct current, or average, component of the signal [1]. With a 10 V sine and a 5 V offset the result is √(25 + 50) = 8.66 V. The offset is added in quadrature, not directly, because the squares add.

Worked examples

A sine wave of 10 V peak has an RMS of 7.07 V. A square wave of 10 V peak-to-peak has 5 V, and a triangle of 10 V peak has 5.77 V. A half-wave rectified sine of 10 V peak has 5 V, and a full-wave rectified one has 7.07 V [2]. Try each in the waveform list to confirm that the calculator matches them.

Crest factor

The result page also gives the crest factor, the peak amplitude divided by the AC RMS value [3]. It is 1.414 for a sine wave, 1 for a square wave and 1.732 for a triangle or sawtooth [3]. A high crest factor means short peaks above the RMS level, which matters when you choose an amplifier or a meter. Wikipedia's RMS table gives the same value for the sawtooth as for the triangle [1].

Measuring real signals

A cheap average-responding meter assumes a sine wave and scales its reading, so it is wrong for other shapes. A true-RMS meter computes the real value. The calculator gives the ideal result for a clean waveform. If your signal is distorted, noisy or a pulse with a duty cycle other than 50 percent, the formulas on this page do not apply, and you should measure it.

Using the result

Use the RMS voltage with Ohm's law to find the heating power, P = V² ÷ R, or the RMS current. If you have the RMS value and want the power into a speaker or a load, our RMS to watts calculator does that step. For the peak you need to withstand, for instance in a capacitor rating, use the equivalent peak value that this page also prints.

Choosing the waveform

A sine wave is the shape of mains power and of the output of a signal generator in its sine setting. A square wave is typical of digital logic and switching supplies, a triangle or a sawtooth of oscillators and ramps, and the rectified waves of the output of diodes in a power supply before smoothing. Pick the one that matches the signal on your oscilloscope, and enter the value you can read from its screen.

Peak, peak-to-peak and average

The oscilloscope usually shows the peak-to-peak value most easily, as the distance between the highest and lowest points of the trace. A multimeter in its normal mode shows an RMS or a scaled average value. By offering all three on the input side, the calculator lets you start from whichever one you actually have, and the result is the same RMS figure that you would get from a true-RMS meter, if the signal is a clean waveform.

Common mistakes

  • Using the peak value as if it were the RMS. The RMS of a sine is 0.707 of its peak.
  • Adding the offset directly. The offset adds in quadrature.
  • Using Vavg for a triangle. This tool does not support it.
  • Applying sine factors to a square wave. Each waveform has its own factor.

What next

Use this often? Add RMS Voltage to your Home screen.

Frequently asked questions

What is an rms voltage calculator?

A tool that converts a peak, peak-to-peak or average voltage into the RMS value of the waveform.

What is the RMS voltage of a sine wave?

The peak voltage divided by √2, so about 0.707 of the peak.

How do I add a DC offset to the RMS voltage?

Take the square root of the offset squared plus the AC RMS squared.

What is the RMS of a square wave?

It equals the peak voltage, or half of the peak-to-peak voltage.

Why is Vavg missing for triangle waves?

This tool does not offer an average-voltage input for triangle or sawtooth waves, because the relation used for rectified sine waves does not apply to them, so we left it out.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools