Saved

Press the star next to a tool's name to save it.

All my tools

Rebar Calculator

This rebar calculator counts the bars a concrete slab needs from its size, bar spacing and cover, then gives the stock bars to buy, the steel's weight and its cost.

Restored your last values ·

Bars run both ways in a square grid. Leave cover, lap and waste empty for 0. An empty stock length counts as 20 ft (6 m in metric). Enter the lap length your plans or engineer give for runs longer than one bar.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Rebar to buy

–

Enter the slab size and the bar spacing.

See full result

A rebar calculator works out how many reinforcing bars a concrete slab needs, how much the steel weighs and what it costs. Enter the slab's length and width, the bar size, the spacing between bars and the edge cover, and the calculator lays out a grid of bars running both ways. It counts the bars in each direction, adds splices where a run is longer than one stock bar, and tells you how many stock bars to buy. US units (feet, inches, pounds) are the default, and you can switch to meters, centimeters and kilograms.

How the rebar calculator counts bars

Rebar in a slab usually sits in a grid. Bars that run along the slab's length are spaced across its width, and bars that run along the width are spaced along its length. Each bar stops short of the edge by the cover distance, so concrete protects the steel. The count in each direction is:

  • Bars along the length = (width − 2 × cover) ÷ spacing, rounded down, plus 1
  • Bars along the width = (length − 2 × cover) ÷ spacing, rounded down, plus 1
  • Length of each bar = the slab side − 2 × cover

The extra bar is there because a row of bars has one more bar than gaps. Spacing is measured center to center, which is how plans give it, such as "#4 at 12 in on center".

Rebar sizes and weights

US bar sizes #3 to #8 are numbered in eighths of an inch, so a #4 bar is 4/8 or 1/2 inch across, and a #8 is 1 inch. The calculator uses the nominal diameter, area and weight per foot of standard bars, the typical specification being ASTM A615 Grade 60 deformed bars:

BarDiameterAreaWeight
#30.375 in0.11 sq in0.376 lb/ft
#40.500 in0.20 sq in0.668 lb/ft
#50.625 in0.31 sq in1.043 lb/ft
#60.750 in0.44 sq in1.502 lb/ft
#70.875 in0.60 sq in2.044 lb/ft
#81.000 in0.79 sq in2.670 lb/ft
#91.128 in1.00 sq in3.400 lb/ft
#101.270 in1.27 sq in4.303 lb/ft
#111.410 in1.56 sq in5.313 lb/ft

In metric mode the same bars are shown with their diameter in millimeters, and the weight is converted to kilograms per meter (1 lb/ft is about 1.488 kg/m). The calculator also shows the steel area per foot of slab: the bar's area × 12 ÷ the spacing in inches. A #4 bar at 12 inches gives 0.20 square inches per foot, which matches the standard spacing tables engineers use.

Worked example: a 20 ft × 20 ft slab

Say you're pouring a 20 ft by 20 ft garage slab with #4 bars at 12 inches on center, 3 inches of cover and 20 ft stock bars.

  1. Each bar is 20 ft − 2 × 3 in = 234 in, or 19.5 ft long.
  2. Bars each way: 234 ÷ 12 = 19.5, rounded down to 19, plus 1 = 20 bars.
  3. Total steel: 40 bars × 19.5 ft = 780 ft.
  4. Weight: 780 ft × 0.668 lb/ft = 521.0 lb.
  5. Stock bars: each 19.5 ft bar is cut from one 20 ft bar, so you buy 40 bars.

Notice that 780 ft ÷ 20 ft is only 39, but you can't join the short offcuts into a usable bar, so the calculator counts whole bars per cut. Enter a waste percentage if you want a few spares on top.

Long runs, splices and laps

When a run is longer than one stock bar, two bars are overlapped and tied together. That overlap is the lap, and it uses extra steel. Enter the lap length from your drawings; the calculator adds one lap for every splice and counts the pieces each run needs.

For example, a 40 ft × 12 ft driveway strip with #4 bars at 18 inches, 3 inches of cover, 20 ft stock bars and a 24 inch lap needs 8 bars along the length, each about 39.5 ft and made from three pieces, and 27 bars across the width. That's 658.5 ft of steel weighing about 440 lb, 16 splices and 45 stock bars to buy.

Steel bar quantity and cost

Many people search for a steel bar quantity estimator or a steel bar cost calculator because they're pricing a job before ordering. Enter the price of one stock bar and the calculator multiplies it by the bars to buy. Prices vary by supplier, bar size and grade, so use a current quote. Remember chairs, tie wire and cutting or bending, which aren't included.

Choosing the spacing and size

The bar size and spacing come from the slab's design, not from this tool. Closer spacing or larger bars put more steel in each foot of slab. If two layouts give similar steel area per foot, the one with fewer, larger bars is usually quicker to place, while smaller bars at closer spacing spread the steel more evenly. Check with your plans, local building department or a structural engineer before you buy.

Common mistakes

  • Forgetting the cover. Bars that run edge to edge leave the steel exposed. The cover is subtracted at both ends and both sides.
  • Dividing total feet by bar length. That ignores offcuts and usually leaves you a bar or two short.
  • Leaving out laps. Spliced runs use more steel than the run's length.
  • Mixing units. In US mode the slab is in feet but the spacing, cover and lap are in inches.

What next

Use this often? Add Rebar to your Home screen.

Frequently asked questions

How does a rebar calculator work out the number of bars?

It subtracts the edge cover from each side of the slab, divides by the spacing, rounds down and adds one bar, in each direction. Then it works out how many stock bars those runs can be cut from.

How much does #4 rebar weigh?

A #4 bar weighs 0.668 lb per foot. A 20 ft bar weighs about 13.4 lb.

What spacing should rebar be in a slab?

That depends on the slab's design, load and thickness, so take it from your plans or an engineer. The calculator works with any spacing from 2 to 120 inches.

Can I use it as a steel bar cost calculator?

Yes. Enter the price of one stock bar, and the calculator multiplies it by the number of bars to buy. Tie wire, chairs and delivery aren't included.

Does it work in meters?

Yes. Switch to metric to enter the slab in meters and the spacing, cover and lap in centimeters. Results are in meters and kilograms.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools