A PSU wattage calculator estimates the size of power supply a PC needs. You add up the power of the CPU, the graphics card and everything else, then leave some headroom, and the tool rounds up to a standard unit size. This page uses the maker’s published power figures, so you can build or upgrade a computer without guessing.
How to use the PSU wattage calculator
- Enter the CPU power, normally its TDP from the maker’s spec page.
- Enter the graphics card’s total board power from its spec page.
- Estimate other parts, such as the motherboard, memory, drives, fans and USB devices, and enter the total. Around 50 to 100 watts is a common guess for a typical desktop.
- Choose whether to plan for the CPU at its TDP or at 1.5 times its TDP.
- Set the headroom, or leave it at 30%, then press Calculate.
The PSU sizing formula
The estimated load is the CPU power plus the graphics card power plus other parts. The recommended minimum is that load times one plus the headroom. The tool then picks the next standard size in a list that runs from 350 up to 1,600 watts. The list is our own selection of common retail sizes.
Why leave headroom
Wikipedia says power supplies are designed around 40% greater than the calculated system power consumption, which protects against performance problems and overloading. [1] Headroom also covers short power spikes. A supply that theoretically fits the sum of the component powers may still trigger its overload protection. [1] This calculator defaults to 30% as our own working figure and lets you change it. Use 40% to follow the figure on the page above.
TDP is not peak power
Thermal design power is the maximum amount of heat a component is expected to generate in ordinary use. It is not a hard ceiling on power draw. Some sources put a processor’s peak power at about 1.5 times its TDP, and the actual power can be higher or much lower than TDP. [2] That is why the calculator has a peak option that multiplies the CPU power by 1.5. Choose it for overclocked or heavily loaded systems.
Worked example
A build has a 125 W CPU, a 320 W graphics card and about 80 W for other parts. The load is 525 watts. With 30% headroom the minimum is 682.5 watts, which rounds up to a 750 watt supply. That unit would run at 70% load. With the peak option, the CPU counts as 187.5 W and the load becomes 587.5 watts, so the minimum is about 764 watts and the next standard size is 850 watts.
| Build | Load | With 30% headroom | Standard size |
|---|---|---|---|
| Office PC, 65 W CPU, no card, 40 W other | 105 W | 137 W | 350 W |
| Mid-range gaming, 105 W CPU, 200 W card, 60 W other | 365 W | 475 W | 500 W |
| High-end gaming, 125 W CPU, 320 W card, 80 W other | 525 W | 683 W | 750 W |
Efficiency and load
The energy efficiency of a power supply drops significantly at low loads and generally peaks at about 50 to 75% load, and an oversized unit is often less efficient and wastes more electricity at lower loads. [1] The result therefore shows the load on the unit you are buying. A figure between about 35% and 80% is a sensible zone. Above 80% leaves little room for spikes, and far below 35% means a bigger supply than you need.
Picking a power supply
- Check the graphics card maker’s recommended power supply as well. It may be higher than your sum.
- Make sure the unit has the right connectors for the card and the motherboard.
- Look at the 12 volt rating. The total 12 V output must be higher than the current needed by the CPU and the graphics card.
- Choose a reputable brand with an efficiency certificate such as 80 Plus. Wikipedia notes that some self-certified units may claim output roughly double what they deliver. [1]
- Allow for future upgrades if you plan a stronger graphics card.
Where to find the power figures
Look at the product page of the CPU for its TDP and at the graphics card page for its total board power, which is sometimes called total graphics power. Both makers publish these numbers on their official spec pages. For other parts, a typical desktop motherboard, a few memory modules, a couple of drives and several fans add up to a modest amount compared with the CPU and graphics card. If you have many drives, add each one separately.
Peak load and transient spikes
Modern graphics cards can draw short bursts of power above their rated figure for a fraction of a second. A supply with generous headroom handles these without tripping its protection. If your computer restarts under heavy load, an undersized or aging supply is one possible cause. Choosing the peak option and 40% headroom gives a more cautious result.
Upgrading later
If you may fit a stronger graphics card later, size the supply for that card now. Replacing a power supply means opening the case and rerouting cables. Leave some headroom for extra drives, USB devices and cooling. Turn off the calculator’s default only when you are sure the build will stay as it is.
Common mistakes
- Adding up the power of each part but forgetting drives, fans and USB devices.
- Using the TDP as the maximum power draw of the CPU.
- Choosing a unit with exactly the sum, with no headroom.
- Buying a very large unit for a small build, which costs more and may be less efficient at idle.
What next
Use this often? Add PSU Wattage to your Home screen.
Frequently asked questions
How do I use a PSU wattage calculator?
Enter the CPU power, the graphics card power and other parts, choose the headroom and press Calculate. You get the load and the standard supply size to buy.
How much headroom should a power supply have?
Wikipedia says power supplies are designed around 40% above the calculated system consumption. This tool defaults to 30% and lets you change it.
Is TDP the same as power draw?
No. TDP is the heat a component is designed to give off. Actual power can be higher or lower, and a CPU can exceed its TDP under heavy load.
What load is best for a power supply?
Efficiency generally peaks at about 50 to 75% load and drops at low loads, so a unit running between about 35% and 80% of its rating is a sensible target.
Does this replace the graphics card maker’s advice?
No. Check the graphics card maker’s recommended power supply and connector needs as well, and use the higher of the two.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.