A percent ionic character calculator estimates how ionic a chemical bond is. Choose two atoms or enter their electronegativities and it applies the Pauling and Hannay–Smyth formulas. If you know the measured dipole moment and the bond length, it works out the percentage from the dipole instead.
How to use the percent ionic character calculator
- Choose what you know.
- Select the two atoms, or enter the dipole moment and bond length.
- Press Calculate.
Bond polarity
In a bond between two different atoms, the more electronegative atom draws the shared electrons toward itself, so one end is slightly negative and the other slightly positive. The bond dipole is calculated by multiplying the amount of charge separated by the distance between the charges [1], and the dipole moment has the magnitude p = q × d [4]. The debye unit equals 3.33564 × 10⁻³⁰ coulomb metres [1].
Electronegativity differences
The page lists Pauling electronegativities: hydrogen 2.20, lithium 0.98, carbon 2.55, nitrogen 3.04, oxygen 3.44, fluorine 3.98, sodium 0.93, chlorine 3.16, potassium 0.82, bromine 2.96 and caesium 0.79 [2]. The calculator uses these. As a guide, a difference below 0.5 is nonpolar covalent, between 0.5 and 2.0 is polar, and above 2.0 is ionic [1]. A difference of 1.7 corresponds to about 50 percent ionic character [1].
The two formulas
The Pauling estimate is 100 × (1 − e^(−Δχ²/4)), and the Hannay–Smyth estimate is 16 Δχ + 3.5 Δχ², both with Δχ the electronegativity difference. Neither is written on the pages that we read, so they are standard formulas that we state as our own working. They agree roughly at small differences and drift apart at larger ones: for sodium chloride, Δχ = 2.23 gives 71.15 percent by Pauling and 53.09 percent by Hannay–Smyth. At 1.7 the Pauling formula gives 51 percent, in line with the 50 percent figure above.
Worked examples
Hydrogen bromide has a difference of 0.76, which is polar, and the Pauling formula gives about 13 percent. The carbon–hydrogen bond has a difference of 0.35, so it is nonpolar. Caesium fluoride has a difference of 3.19, close to fully ionic. These values come from our own calculations with the table above.
From the dipole
The second mode compares the measured dipole moment with that of a fully ionic bond, where a full electron charge sits at each end of the bond. For a bond length in ångström, one electron charge separated by that length has a dipole of 4.8032 debye per ångström, a conversion we derive from the elementary charge and the debye. The page's figure that 1 D corresponds to charges separated by 0.208 Å is consistent with it [1]. Percent ionic character is then the observed moment divided by this value.
A dipole example
The page gives gas-phase potassium bromide a dipole moment of 10.41 D [1], a highly ionic molecule. With a bond length of 2.82 ångström, a figure we take from outside the pages, the ionic value would be 13.55 D and the bond is about 77 percent ionic. The calculator accepts any bond length you supply.
Ionic or covalent
The page on ionic bonding describes bonding on a continuum, with no sharp line between ionic and covalent bonds [3]. Percent ionic character expresses that idea in one number. Use it to rank bonds, to compare compounds and to see why a salt such as sodium chloride is ionic while hydrogen bromide is a polar molecule.
Trends across the table
Electronegativity rises across a period and falls down a group, so bonds between elements far apart on the table are the most ionic. Alkali metal halides lie near the top of the scale, with caesium fluoride the most ionic of the common ones, while bonds between carbon and hydrogen or between the halogens themselves are nearly nonpolar. Run a few pairs through the calculator to see this pattern emerge from the numbers.
What the percentage means
A bond that is 50 percent ionic does not have half of the electrons transferred in a literal sense. The figure is a measure of how far the electron distribution lies between the two extremes, and it is defined by the formula you use. That is why the Pauling and Hannay–Smyth numbers differ, and why it is better to rank bonds with one formula than to quote a single value as a fact.
Dipole moments in practice
Dipole moments of gas-phase molecules are measured by microwave spectroscopy and by the Stark effect. Comparing the measured moment with the one for a full charge separation gives a figure that depends on the bond length you use, so take both from the same source.
Choosing a formula
For most classroom problems either formula is accepted, but your course may name one, so check which. The Pauling estimate rises smoothly towards 100 percent, while the Hannay–Smyth expression is capped at 100 in the calculator, since a polynomial would otherwise pass it at large differences.
Common mistakes
- Treating 100 percent as achievable. Even caesium fluoride is not fully ionic.
- Mixing electronegativity scales. Use Pauling values for the formulas.
- Using the formulas for large differences without care. They disagree.
- Entering the bond length in the wrong unit. Enter ångström.
What next
Use this often? Add Percent Ioni to your Home screen.
Frequently asked questions
What is a percent ionic character calculator?
A tool that estimates how ionic a bond is from the electronegativity difference or from the dipole moment.
What is the Pauling formula?
% ionic = 100 × (1 − e^(−Δχ²/4)), with Δχ the electronegativity difference.
What is the Hannay–Smyth formula?
% ionic = 16 Δχ + 3.5 Δχ².
When is a bond ionic?
By the usual guide, when the electronegativity difference is above 2.0. About 1.7 is 50 percent ionic.
How do I find ionic character from a dipole moment?
Divide the measured dipole moment by the moment of a full charge separated by the bond length.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.