An open channel flow calculator uses Manning's equation to find the velocity and the flow rate of water in a ditch, a canal or a part-full pipe. Enter the roughness, the slope, the depth and the size of the channel, and it also gives the flow area, the wetted perimeter and the hydraulic radius.
How to use the open channel flow calculator
- Choose US or metric units and the shape.
- Enter the roughness n and the slope.
- Enter the depth and the width, side slope or diameter.
- Press Calculate.
Manning's equation
Manning's equation is V = (1 ÷ n) × R^(2/3) × s^(1/2), where V is the velocity, n is the roughness coefficient, R the hydraulic radius and s the slope of the bottom of the channel [1]. The flow rate then follows from Q = V × A, with A the cross-sectional area [1]. Wikipedia writes the law with a constant k, equal to 1 in SI units and 1.49 in English units [1]. It describes open-channel flow as flow with a free surface, and Manning's equation as the most common method for calculating it [3]. The calculator applies it for the four shapes.
The hydraulic radius
The hydraulic radius is the area of the flow divided by the wetted perimeter, R = A ÷ P [2]. The wetted perimeter is the length of the channel's cross-section that the water touches. This is why the same tool also serves as a hydraulic radius calculator: the result shows A, P and R for the channel that you enter. For a full circular pipe, Wikipedia says that R is one quarter of the hydraulic diameter [2], which is the pipe diameter, our reading, and the tool gives D ÷ 4.
The shapes
For a rectangle, A = b × y and P = b + 2y. For a trapezoid with a side slope of z, A = (b + z × y) × y and P = b + 2y × √(1 + z²). A triangle is a trapezoid with a bottom width of zero. A part-full circular pipe uses the angle θ = 2 × arccos(1 − 2y ÷ D), with A = D² × (θ − sin θ) ÷ 8 and P = D × θ ÷ 2. The sources do not give these geometry formulas, so they are our own working.
Units and the constant
In metric mode, lengths are in metres and the constant is 1. In US mode, lengths are in feet and the constant is 1.4859, the exact figure which Wikipedia gives behind its rounded 1.49 [1]. The slope is a plain ratio, for example 0.001 for a drop of 1 metre in 1,000 metres. Results are given in cubic metres per second or cubic feet per second, with the other unit in brackets, and litres per second in metric mode.
Choosing the roughness
Roughness depends on the surface, for example concrete, asphalt or wood, and the calculator takes n as an input. Wikipedia gives the reciprocal, from 20 for rough stone to 80 for smooth concrete and cast iron in metric units [1], which is a roughness of about 0.0125 to 0.05, our own arithmetic. Enter the value that your design guide gives for your surface.
A worked example
A rectangular concrete channel is 2 metres wide, with water 0.5 metres deep, a slope of 0.001 and n = 0.013. The area is 1 square metre, the wetted perimeter is 3 metres, and the hydraulic radius is 0.3333 metres. The velocity is (1 ÷ 0.013) × 0.3333^(2/3) × 0.001^(1/2) = 1.1694 metres per second, and the flow is 1.1694 cubic metres per second. This worked example is our own.
The same channel in feet
Enter the same channel in US units: a width of 6.56 feet, a depth of 1.64 feet. The tool returns 41.3 cubic feet per second, which is 1.1694 cubic metres per second, and a velocity of 3.84 feet per second. The agreement shows that the two unit systems give one answer, as they should, when the constant is 1.4859 for feet. This is a handy check on the settings.
Slope and depth
The flow grows with the square root of the slope: four times the slope doubles the velocity. It grows more than in proportion to the depth, since both the area and the hydraulic radius increase. Wikipedia notes that the slope S is the same as the bed slope when the depth is uniform [1]. If the depth changes along the channel, the equation is not accurate, and a backwater analysis is needed.
Most efficient shapes
The usual most efficient sections of channel design are a half-filled square for a rectangle, a half-filled regular hexagon for a trapezoid, a half-filled tilted square for a triangle, and a depth equal to the radius for a circle. These shapes give the smallest wetted perimeter for the area, and so the largest hydraulic radius. You can test them: a 1 metre by 0.5 metre rectangle has a larger R than a flat, wide one with the same area.
Using the calculator
Pick the shape, enter n and the slope, and then the dimensions. For a pipe, the depth may not be more than the diameter. Read the velocity and the flow, and look at the hydraulic radius. Change n to see how a rougher surface cuts the flow in proportion, and compare shapes with the same area. For anything that matters, such as a drain or a spillway, ask an engineer to check the design.
Common mistakes
- Using the wrong unit system. Check the US and metric switch.
- Entering the slope in percent. Use a ratio: 1 percent is 0.01.
- Using the depth of a pipe above its diameter. Use a full pipe instead.
- Treating n as exact. Roughness is an estimate.
What next
Use this often? Add Open Channel to your Home screen.
Frequently asked questions
What is an open channel flow calculator?
A tool that finds the velocity and flow of water in a channel with a free surface, from Manning's equation.
What is the Manning equation?
V = (1 ÷ n) × R^(2/3) × S^(1/2) in metric units, and Q = V × A.
What is the hydraulic radius?
The flow area divided by the wetted perimeter, R = A ÷ P.
What is the constant in US units?
1.49, or more exactly 1.4859, in place of 1 for metric units.
Does the tool work for a pipe?
Yes, for a pipe that is part full; the full-pipe hydraulic radius is a quarter of the diameter.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.