A modulation calculator finds the modulation index of an amplitude modulated (AM) or frequency modulated (FM) signal, and the bandwidth that it takes up. For AM, enter the carrier and message amplitudes. For FM, enter the peak frequency deviation and the highest message frequency. You get the index and a bandwidth.
How to use the modulation calculator
- Choose AM or FM.
- Choose the frequency unit.
- Enter the amplitudes (AM) or the deviation and message frequency (FM).
- Press Calculate.
What modulation is
Modulation puts a message signal onto a higher-frequency carrier so that it can be sent by radio. In amplitude modulation the message changes the amplitude of the carrier; in frequency modulation it changes the frequency. The modulation index says how strongly the carrier is varied. It is the number that a transmitter designer, a student or a radio amateur checks first, since it sets the quality of the signal and the space it takes in the radio spectrum.
The AM modulation index
Wikipedia defines the AM modulation index as the peak change in the carrier amplitude divided by the carrier amplitude, m = M ÷ A, where M is the modulation amplitude and A the carrier amplitude [1]. In practice it is the message amplitude over the carrier amplitude. For example, a 40 volt message on a 50 volt carrier gives 0.8, and the calculator shows it as 80% modulation.
Overmodulation
If the index is above 1, the message changes the carrier by more than its own amplitude, which is called overmodulation. Wikipedia says that the original message then cannot be reliably recovered from the transmitted signal [1]. The calculator flags any result above 1. For example, a 50 volt message on a 40 volt carrier gives an index of 1.25. A transmitter is normally kept at or below 1, which is 100%.
AM bandwidth and sideband power
The RF bandwidth of AM is twice the bandwidth of the baseband signal [1], so a 15 kHz message needs 30 kHz. If you enter the highest message frequency, the calculator gives this. It also gives the sideband power as a share of the carrier power. For a sine message the two sidebands carry m² ÷ 2 of the carrier power, which is our own working; at 100% modulation, that is half, consistent with the statement on Wikipedia that the carrier has twice the power of the sidebands [1].
The FM modulation index
Wikipedia writes the FM index as h = Δf ÷ f m, the peak frequency deviation divided by the highest frequency in the modulating signal [2]. FM broadcast deviation is up to 75 kHz [2]. With a highest message frequency of 15 kHz, the index is 5. Choose FM, enter 75 and 15 in kilohertz, and you get this result.
Carson's rule
The bandwidth of an FM signal is estimated with Carson's rule, B = 2 (Δf + f m), which Wikipedia also writes as 2 f m (h + 1); it is a rule of thumb for a sine-wave message [2]. For the broadcast example the bandwidth is 2 × (75 + 15) = 180 kHz. The result is shown in the unit you chose for the frequencies.
Narrowband and wideband FM
Wikipedia calls the signal narrowband FM when the index is much less than 1, with a bandwidth of about 2 f m, and says some sources use 0.3 as the limit; it calls it wideband FM when h is much greater than 1, with a bandwidth of about 2 Δf [2]. The calculator labels an index below 0.3 as narrowband and above 1 as wideband. Between those two values it says so in plain words; that wording is our own.
Choosing the frequency unit
The deviation and the message frequency must be in the same unit. Pick hertz, kilohertz or megahertz and enter both values in it. The index is a ratio, so it does not depend on the unit, but the bandwidth is given in the unit you chose. For the broadcast example in megahertz, 0.075 and 0.015 give an index of 5 and a bandwidth of 0.18 MHz.
The regime depends on the index
A common textbook shortcut says that the index is between 0 and 1 for AM and always greater than 1 for FM. The FM claim is a simplification: narrowband FM has an index well below 1 [2]. The calculator therefore reports the regime from the actual value of the index, and not from the type of modulation.
Limits
All these formulas assume a single sine-wave message. Real speech and music contain many frequencies, and transmitters are subject to national limits on bandwidth and deviation. The calculator gives you the textbook index and bandwidth, and no more. Use the rules of your regulator, and the data sheet of your equipment, for anything you will transmit.
Common mistakes
- Swapping the carrier and the message. The message amplitude goes in the numerator for AM.
- Mixing frequency units. Use the same unit for the deviation and the message frequency.
- Using the lowest frequency instead of the highest. The highest message frequency sets the bandwidth.
- Treating Carson's rule as exact. It is a rule of thumb for a sine message.
- Letting an AM index go above 1. That is overmodulation.
What next
Use this often? Add Modulation to your Home screen.
Frequently asked questions
What is a modulation calculator?
A tool that finds the modulation index of an AM or FM signal, with its bandwidth.
What is the AM modulation index formula?
m = message amplitude ÷ carrier amplitude.
What is the FM modulation index formula?
Index = peak frequency deviation ÷ highest message frequency.
What is Carson's rule bandwidth?
B = 2 × (deviation + highest message frequency), a rule of thumb for a sine message.
What happens if the AM index is above 1?
The carrier is overmodulated and the message cannot be recovered reliably.
Is an FM index always greater than 1?
No. Narrowband FM has an index well below 1.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.