A lumber weight calculator estimates how much a board or a beam weighs from its species, its size and its length. It multiplies the volume of the piece by the density of the wood, and it can fill in the actual size of a nominal board, such as a 2 × 4, which is smaller than its name.
How to use the lumber weight calculator
- Choose US or metric units.
- Pick the species, or choose Other and type a density.
- Choose a nominal size from the chart, or switch to actual size and type the thickness and width.
- Enter the length and the number of pieces, then press Calculate.
The formula
The weight of a piece of lumber is its volume times the density of the wood. The volume is the thickness times the width times the length. In the tool, the thickness and width in inches are multiplied and divided by 144 to give square feet, and that is multiplied by the length in feet, which is our own working. The weight in kilograms is the weight in pounds times 0.45359237.
Nominal and actual sizes
A board sold as a 2 × 4 does not measure 2 by 4 inches. A 2 × 4 now measures about 1 1/2 by 3 1/2 inches, because of kiln drying and planing [2]. The dressed sizes are: 1 × 2 is 3/4 by 1 1/2, 1 × 4 is 3/4 by 3 1/2, 2 × 6 is 1 1/2 by 5 1/2, 2 × 8 is 1 1/2 by 7 1/4 and 4 × 4 is 3 1/2 by 3 1/2 [1]. The tool deals with this difference with a chart.
A 4 × 4 taken at its name
This example is our own. Take a 4 × 4 of 6 feet at 67 pounds per cubic foot. Taken as 4 by 4 inches, the area is 16 square inches or 0.1111 square feet, the volume is 0.6667 cubic feet, and the weight is 44.67 pounds. To reproduce it, choose actual size, type 4 and 4, and use Other with a density of 67.
A real 4 × 4
A real 4 × 4 is 3 1/2 by 3 1/2 inches, which is 12.25 square inches or 0.08507 square feet. Six feet of it is 0.5104 cubic feet, and in white oak at 64 pounds per cubic foot it weighs 32.67 pounds [1][3]. That is 23.4 percent less wood than the nominal 16 square inches suggests, so a calculation made with the name of the board overstates the weight by about a third. This is why the tool starts from the nominal size chart.
A 2 × 4 in pine
This example is our own. A ponderosa pine 2 × 4 of 8 feet, at 46 pounds per cubic foot, has an actual size of 1.5 by 3.5 inches, a volume of 0.2917 cubic feet and a weight of 13.4 pounds [2][3]. If you used the nominal 2 by 4 inches, you would get 0.4444 cubic feet and 20.4 pounds. The real board holds 34 percent less wood than the name suggests, and the tool prints that gap whenever you pick a nominal size.
Where the densities come from
The species list is Table 1 of a Penn State Extension article, which gives average green weights in pounds per cubic foot for 63 North American species [3]. Examples are 64 for white oak, 61 for northern red oak, 59 for sugar maple, 50 for loblolly pine and 46 for ponderosa pine. If your species is not in the list, choose Other and type a density. In metric mode the density is in kilograms per cubic metre.
Green weight, not dry weight
The Penn State figures are for green wood, that is wood just after the tree is cut. Lumber is normally sold dry, so a dry board weighs noticeably less than the tool shows. We use the green table because it is the one that we can cite in full, and it gives a safe upper estimate for shipping or lifting. Where you know the density of the dried wood, choose Other and type that instead.
Pine against oak
Pine is often said to be much lighter than oak, and the table lets us put a number on it. In the Penn State table, the green weight of ponderosa pine is 46 pounds per cubic foot and that of white oak is 64, so the pine is about 28 percent lighter, by our own working [3]. Loblolly pine, at 50, is 22 percent lighter than white oak. The gap depends on the two species that you compare.
Weight per length and many pieces
The result lists the weight of one piece and of all the pieces together, the volume, and the weight per foot, with the kilograms per metre next to it. The weight per length helps when you plan the load on a trailer or a shelf, or pay for shipping by the foot. Enter the number of pieces as a whole number. The size line states which size was used, from the chart or typed in.
Limits
Actual sizes vary between suppliers and standards, so measure a piece when it matters. Treated lumber weighs more than untreated and the tool has no figure for pressure treatment. We did not open the lumber standard itself. The densities are averages, and a single board can differ. The answer is an estimate for planning, and it is not a structural load figure.
Common mistakes
- Using the nominal size as the real size. A 2 × 4 is about 1 1/2 by 3 1/2 inches.
- Reading the answer as a dry weight. The densities are for green wood.
- Mixing units. Use inches and feet in US mode, and millimetres and metres in metric mode.
- Forgetting the number of pieces. Enter it to get the total.
What next
Use this often? Add Lumber Weigh to your Home screen.
Frequently asked questions
What is a lumber weight calculator?
A tool that estimates the weight of a board or beam from its species, size and length, using the volume and the density of the wood.
How much does a 2 × 4 weigh?
An 8 foot ponderosa pine 2 × 4 of 1.5 by 3.5 inches has a volume of 0.2917 cubic feet and weighs about 13.4 pounds at the green density of 46.
What is the actual size of a 2 × 4?
About 1 1/2 by 3 1/2 inches, because of drying and planing.
Does the calculator use green or dry weights?
Green weights, so a dry board weighs less than the tool shows.
How do I calculate the weight of a piece of lumber?
Multiply its volume by the density of the wood. The volume is the thickness times the width times the length.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.