A linear actuator force calculator estimates the maximum force that a hydraulic, pneumatic or electric actuator must deliver to push a load along a flat surface or up a slope. It adds the pull of gravity along the slope, the friction and the force needed to accelerate the load.
How to use the linear actuator force calculator
- Choose US or metric units.
- Enter the mass, the stroke length, the stroke time and the friction coefficient.
- Add the slope angle, or leave it blank for a horizontal push.
- Press Calculate and read the force and its three parts.
The inclined plane formula
For a load on a slope, the force is T = m g sin θ + μ m g cos θ + m a [2]. The three terms are the part of the weight that pulls the load down the slope, the friction force and the force that accelerates the load. The static friction coefficient is used because the result is a maximum force [3].
The horizontal formula
On a flat surface the slope is zero, so the gravity term vanishes and the formula becomes T = μ m g + m a. In the calculator, a blank or zero angle uses the same expression. Setting θ = 0 in the inclined formula gives exactly the horizontal one, since sin 0 is zero and cos 0 is one.
Speed and acceleration
The tool assumes that the actuator speed rises from zero to a peak value at the end of the stroke. The velocity is V = stroke ÷ time, and the acceleration is a = stroke ÷ time². This is a simplification with no velocity profile, and it gives a first approximation. The calculator shows both figures so you can judge them.
Gravity
The calculator uses g = 9.81 m/s², a rounded form of the standard value of 9.80665 m/s² [4]. In US mode, the mass in pounds is converted to kilograms with the standard factor 0.45359237, and the force is shown in newtons and in pounds-force. These conversions are our own working.
A worked example
Take a 150 kg block on a 25° incline, pushed 10 m in 40 s with μ = 0.68. The speed is 0.25 m/s and the acceleration is 0.00625 m/s². Gravity along the slope gives 621.9 N, friction gives 906.9 N and inertia gives 0.94 N, so the total is about 1,529.7 N. The calculator gives this figure.
What the three parts tell you
In the example, friction is the biggest part and the inertia is almost nothing, because the stroke is slow. If you shorten the stroke time, the acceleration grows with the inverse square of the time, and the inertia term can become large. Halving the time multiplies the inertia force by four.
Choosing an actuator
Once you have the maximum force, you can look for an actuator with a rating above it. The next step is to check manufacturers' ratings for a suitable unit. Real ratings should include a safety factor, which this tool does not apply. Ask the manufacturer to confirm the unit for your load before you buy it.
How lead screw actuators deliver force
A lead screw has a continuous helical thread along its length, and a nut that cannot rotate is driven along it [1]. The speed and force of the actuator depend on its gearbox, and the gearing trades speed for torque so that the motor can turn the screw under a heavy load [1]. Wikipedia gives no formula that links the motor torque to the thrust, so this tool does not either.
Limits of the model
The result is a first approximation, covers translational motion only and cannot be used for rotating applications. It does not include the weight of the actuator, the side loads, the stiffness of the mount, the wear of the guides or the change of friction with speed. The overall length of an actuator is also more than the stroke.
Safety
A load that is moved by an actuator can crush, trap or fall. Do not use this estimate alone for anything that carries people, lifts overhead or protects someone. Use the ratings, factors of safety and standards that apply to your equipment, and have a qualified engineer approve the design.
Reducing the force needed
Three changes lower the result. A longer stroke time cuts the inertia term sharply, a smoother or lubricated surface lowers the friction coefficient, and a gentler slope reduces both the gravity term and the friction term. Try each in the calculator to see which one gives the biggest saving for your load, then confirm the change with a real test.
Next steps after the estimate
Write down the maximum force, the stroke and the speed. These three figures are what a supplier needs to suggest a hydraulic, pneumatic or electric actuator. Ask about the duty cycle, the mounting and the side loads as well, because the calculator ignores them. A qualified engineer should approve the final choice.
Common mistakes
- Using the kinetic friction coefficient. Use the static one for the maximum force.
- Entering the angle in radians. Enter degrees.
- Forgetting the safety factor. Choose a unit with a rating well above the result.
- Using it for a rotating load. The model covers straight-line motion only.
What next
Use this often? Add Linear Actua to your Home screen.
Frequently asked questions
What is a linear actuator force calculator?
A tool that estimates the maximum force an actuator needs to move a load, from the load's mass, the stroke, the time and the friction.
What is the formula for the force on an incline?
T = m g sin θ + μ m g cos θ + m a, using the static friction coefficient.
How is the acceleration found?
As the stroke length divided by the stroke time squared, assuming a rise from rest.
Can I use the result to pick an actuator?
Only as a first estimate. Add a safety factor and check the manufacturer's rating.
Does it work for rotating motion?
No, it covers straight-line motion only.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.