Saved

Press the star next to a tool's name to save it.

All my tools

Ligation Calculator

Use this ligation calculator to find how much insert to add to a vector at a chosen molar ratio such as 3 to 1, with volumes and a check of the total DNA concentration.

Restored your last values ·

Enter the vector and insert lengths in base pairs, the mass of vector, and the molar ratio of insert to vector. You get the mass of insert to add. Add the concentrations to get volumes, and the reaction volume to check the total DNA concentration.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the vector and insert lengths, then press Calculate.

See full result

A ligation calculator works out how much insert DNA to add to a given amount of vector for a ligation, at a chosen molar ratio. Enter the lengths of the vector and the insert, the mass of vector and the ratio, and it gives the mass of insert, the amounts in femtomoles and, if you enter the concentrations, the volumes to pipette.

How to use the ligation calculator

  1. Enter the vector length and the insert length in base pairs.
  2. Enter the vector mass and the molar ratio, or leave them blank for 50 ng and 3 to 1.
  3. Add the concentrations of the stocks and the reaction volume if you want the volumes and a check of the total DNA concentration, then press Calculate.

The usual molar ratio

The Wikipedia article on ligation says that for cloning an insert into a circular plasmid the molar ratio of insert to vector is usually around 3 to 1.[1] It warns that a very high ratio may produce multiple inserts, and that the ratio may be adjusted depending on the size of the insert, with other ratios such as 1 to 1 also used.[1] The calculator uses 3 to 1 unless you enter another ratio.

From moles to mass

Because the vector and insert differ in length, equal masses do not give equal numbers of molecules. A long molecule carries more mass for each molecule, so the insert mass needed for a molar ratio is the ratio times the vector mass times the insert length divided by the vector length. The page we read gives no such formula, so this is our own working from the definition of a mole. For 50 ng of a 3,000 bp vector and a 1,000 bp insert at 3 to 1, the insert is 3 × 50 × 1,000 ÷ 3,000 = 50 ng. At 1 to 1 with a 1,500 bp insert it is 25 ng.

Amounts in femtomoles

The calculator also shows the amounts in femtomoles, using an average of about 650 grams per mole for each base pair of double-stranded DNA. This average is a common convention and not from the page, so it is labelled as our own working. For 50 ng of a 3,000 bp vector, the amount is 25.6 femtomoles, and 50 ng of a 1,000 bp insert is 76.9 femtomoles, a ratio of 3 to 1.

Volumes to pipette

If you enter the concentration of each stock in ng per microlitre, the volume is the mass divided by the concentration. For 50 ng of vector at 25 ng per microlitre, add 2 microlitres. For 50 ng of insert at 10 ng per microlitre, add 5 microlitres. Make up the rest of the reaction volume with buffer, ligase and water according to your own protocol.

Total DNA concentration

The page says that the total DNA concentration used should be less than 10 micrograms per millilitre, because the plasmid needs to recircularize.[1] Because one nanogram per microlitre equals one microgram per millilitre, the calculator divides the total DNA by the reaction volume and compares it. For 100 ng in 20 microlitres, the concentration is 5 micrograms per millilitre, which is under the limit. The page also lists an excessive amount of DNA as a cause of failed ligation.[1]

Temperature and ends

The page says that sticky-end ligations are performed at 12 to 16 °C, at room temperature, or at 4 °C for a longer time.[1] It says blunt-end ligation is much less efficient than sticky-end ligation, typically about 100 times slower, and needs 10 times or more ligase and a higher DNA concentration.[1] The page also says that the vector needs dephosphorylation when you use two blunt ends or a single cut, to avoid self-ligation.[1] The calculator does not choose times or enzyme amounts; follow the protocol for your ligase.

A worked plan

Suppose that you cut a 4,200 bp vector and want to insert a 750 bp fragment at a ratio of 3 to 1 with 50 ng of vector. The insert mass is 3 × 50 × 750 ÷ 4,200 = 26.8 ng. If the vector stock is 20 ng per microlitre, you need 2.5 microlitres, and if the insert stock is 8 ng per microlitre, you need 3.35 microlitres. In a 20 microlitre reaction the total DNA is 76.8 ng, which is 3.84 micrograms per millilitre and under the limit. These are our own calculations from the formulas above.

Adjusting the ratio

If you get few colonies, you can try a higher ratio, such as 5 to 1, or a lower amount of vector. If many colonies contain multiple inserts, lower the ratio, because the page warns that a very high ratio may produce multiple inserts.{1} For very short inserts, such as linkers, a much higher molar excess is often used, but the page gives no figures, so follow the guidance for your enzyme or kit. Keep a control reaction with vector only and no insert to see how much of the background comes from vector that closed on itself.

Preparing the pieces

Measure the concentration of the cut vector and the insert after purification, since losses on a gel or a column can be large. The calculator needs the real concentrations to give the right volumes. Work from the concentration that you measured, not from the amount that you started with.

Common mistakes

  • Using equal masses. Use the molar ratio, which depends on the lengths.
  • Using too much DNA. Keep the total below the limit for recircularization.
  • Using a very high ratio. Multiple inserts may result.

What next

Use this often? Add Ligation to your Home screen.

Frequently asked questions

What is a ligation calculator?

A tool that finds how much insert DNA to add to a given amount of vector, for a chosen molar ratio of insert to vector.

What insert to vector ratio should I use?

A ratio of about 3 to 1 is usual for an insert into a circular plasmid. Other ratios such as 1 to 1 are also used.

How do I calculate the mass of insert?

Insert mass = ratio × vector mass × insert length ÷ vector length. For 50 ng of a 3,000 bp vector and a 1,000 bp insert at 3 to 1, it is 50 ng.

How much DNA can I put in a ligation?

The page says the total DNA concentration should be below 10 micrograms per millilitre, so that the plasmid can recircularize.

Why is blunt-end ligation harder?

It is typically about 100 times slower than sticky-end ligation and needs more ligase and a higher DNA concentration.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools