A laser beam divergence calculator finds how fast a laser beam spreads, from its diameter at two points. It also covers the other common beam jobs: the beam size at a distance, the focused spot size and depth of focus, a laser beam expander and the smallest divergence that is physically possible for a wavelength.
How to use the laser beam divergence calculator
- Choose what to find.
- Enter the beam diameters, distance, wavelength or focal lengths that appear.
- Press Calculate.
What divergence is
Beam divergence is the angle at which a beam spreads as it travels. The divergence calculation applies in the far field, where the beam diameter is measured at two points far from any focus [1]. The result is the full angle, not the half angle, and it is given here in milliradians and in degrees.
The divergence formula
The full-angle divergence is Θ = 2 · arctan((D_f − D_i) ÷ (2 l)), where D_i and D_f are the initial and final diameters and l is the distance between the two points [1]. For example, a beam of 4 millimetres that is 7.5 millimetres wide after 10 metres has a divergence of about 0.35 milliradians. Enter those values to see the same result. The final diameter must be larger than the initial one.
Beam size at a distance
The calculation also runs in reverse. Solving the formula for the final diameter gives D_f = D_i + 2 l × tan(Θ ÷ 2), which is our own rearrangement. For a beam of 4 millimetres with a divergence of 0.35 milliradians, the diameter after 1 kilometre is about 354 millimetres, more than 35 centimetres. Enter the distance in metres.
Focused spot size
A lens focuses a Gaussian beam to a waist of radius about λ f ÷ (π w), where w is the beam radius at the lens [2]. In terms of diameters this is a spot diameter S = 4 × λ × f ÷ (π × d). This tool multiplies it by the beam quality M² for real beams, which is our own extension: S = 4 × M² × λ × f ÷ (π × d), where λ is the wavelength, f is the focal length and d is the beam diameter at the lens. A red laser of 650 nanometres with M² of 1, a beam of 10 millimetres and a lens of 100 millimetres gives about 8.28 micrometres. The spot size is proportional to the focal length.
Depth of focus
The Rayleigh range of a Gaussian beam is z_R = π w₀² ÷ λ, and the depth of focus is the distance between z = −z_R and z = +z_R, which is twice that [2]. With the spot diameter S = 2 w₀ and the beam quality M², the tool uses z_R = π (S ÷ 2)² ÷ (M² λ), and shows both values. For a green laser of 532 nanometres, M² of 1.12, a lens of 50 millimetres and a beam of 0.5 millimetres, the spot is 75.86 micrometres and the depth of focus is 15.17 millimetres.
Beam expanders
A beam expander is typically built from two lenses, for example as a Galilean telescope, and expanding the beam reduces its divergence [4]. For two lenses, the tool uses the magnifying power MP = f_O ÷ f_I, the output diameter as MP times the input diameter, and the output divergence as the input divergence divided by MP; these are our own working from the lens geometry. Lenses of 25 and 150 millimetres give 6×, a 2 millimetre beam becomes 12 millimetres, and a divergence of 0.4 milliradians falls to about 0.067. A bigger beam spreads less, which is the reason to expand a beam before a long path.
Diameter after the expander
For the beam diameter at a distance L, the tool uses D_L = D_O + L × tan(2 θ_O), with θ_O the output divergence, which gives about 12.67 millimetres at 5 metres in this example. This form differs from the full-angle convention of the divergence formula above, which would give about 12.33 millimetres. Treat the result at long range as approximate.
The smallest divergence
The beam parameter product of a real beam is the half-angle divergence times the waist radius, BPP = M² λ ÷ π, and a Gaussian beam has the lowest possible value, λ ÷ π [3]. Using the full angle and the waist diameter D = 2 w₀, our own working gives θ_min = 4 M² λ ÷ (π D). For 633 nanometres, M² of 1 and 4 millimetres, it is about 0.2015 milliradians. Use it as a floor against which to check a measured divergence.
The beam quality M²
M² describes how close a beam is to an ideal Gaussian beam: 1 is perfect, all real laser beams are above 1 [2], and bigger values mean a worse beam, a larger spot and a larger divergence [3]. Leave the box empty for 1, or enter the figure from the data sheet of the laser. Values below 1 are not possible, and the tool rejects them. Many diode and multimode lasers have M² well above 1, which makes a large difference to the focused spot.
Using the calculator
Pick the calculation and fill in the boxes that appear. For a beam on a bench, measure the diameter at two points far apart, to get the divergence. To plan a lens, use the spot size mode with your wavelength. To plan a long beam path, use the expander mode. Check the safety class of the laser and use eye protection.
Brightness and other limits
This page does not calculate laser brightness, because no formula for it was read from a source. It also does not model aberrations, clipping at apertures or atmospheric effects. For a real system, treat the results as a design starting point, measure the beam, and compare the measured divergence with the smallest value the tool gives.
Common mistakes
- Mixing the units. Diameters and focal lengths are in millimetres, distances in metres.
- Treating the result as exact near the waist. The formulas are for the far field.
- Using the half angle. The divergence here is the full angle.
- Leaving M² at 1 for a real laser. Use the data sheet value.
What next
Use this often? Add Laser Beam D to your Home screen.
Frequently asked questions
What is a laser beam divergence calculator?
A tool that finds the angle at which a laser beam spreads from its diameter at two points.
How do you calculate beam divergence?
Θ = 2 · arctan((final diameter − initial diameter) ÷ (2 × distance)).
How do you find the spot size of a focused laser?
S = 4 M² λ f ÷ (π d), from the wavelength, the focal length and the beam diameter at the lens.
What does a laser beam expander do?
It enlarges the beam by the ratio of the focal lengths and lowers the divergence by the same ratio.
Does this calculator give laser brightness?
No. This tool does not calculate laser brightness; it covers divergence, spot size, expanders and the divergence limit.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.