Saved

Press the star next to a tool's name to save it.

All my tools

Langmuir Isotherm Calculator

Use this Langmuir isotherm calculator to find surface coverage and the amount adsorbed from K and the concentration or pressure, or the Freundlich adsorption amount.

Restored your last values ·

Enter the equilibrium constant K and the concentration or pressure to get the fraction of the surface covered. Add the monolayer capacity to get the amount adsorbed. Or use the Freundlich equation with its two constants.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what you want and fill in the boxes, then press Calculate.

See full result

A Langmuir isotherm calculator gives the fraction of an adsorbent surface that is covered at a given pressure or concentration, and the amount adsorbed when you know the monolayer capacity. It can also work backwards to the concentration, and it includes the Freundlich equation for heterogeneous surfaces.

How to use the Langmuir isotherm calculator

  1. Choose what you want.
  2. Enter the equilibrium constant and the concentration or pressure, and optionally the monolayer capacity.
  3. Press Calculate.

The Langmuir equation

The page gives the Langmuir equation as θ = V / V_m = K p ÷ (1 + K p), where θ is the fractional occupancy of the surface, V is the volume adsorbed, V_m is the monolayer volume and K is the equilibrium constant [1]. It follows from the rates of adsorption and desorption, which depend on the pressure and on the number of free sites, and the equilibrium constant is the ratio of the two rate constants [1]. For solutions, the page gives the same form with activity or concentration, and then K has units of reciprocal concentration [1].

The assumptions

The model assumes a flat, homogeneous surface, with all sites energetically equivalent, each holding at most one molecule, and no interactions between adsorbed molecules [1]. It also assumes that the gas is ideal, that the temperature is constant and that adsorption and desorption are reversible [1]. These are strong assumptions, and real surfaces often break them, which is why other isotherms exist.

Using coverage

At a pressure of 1/K the coverage is exactly one half, which is a quick way to read the constant. For K = 2 per unit pressure and a pressure of 0.5, the coverage is 0.5. For K = 0.2 and a concentration of 5, it is also 0.5. At high pressure the coverage approaches 1 and the surface is a full monolayer. These examples are our own calculations.

Amount adsorbed

With the monolayer capacity q_max, the amount adsorbed is q = q_max × θ, where the mapping of pressure to concentration and of coverage to q ÷ q_max is the usual use in solution, and is our own assumption beyond the page's gas form. With q_max of 10 and a coverage of 0.5, q is 5. The calculator also prints c ÷ q, the quantity used in the linear form c ÷ q = c ÷ q_max + 1 ÷ (K q_max), a rearrangement we have derived.

Concentration for a given amount

To find the concentration that gives a chosen amount adsorbed, rearrange the equation. The page gives K p = θ ÷ (1 − θ) [1], so the concentration is c = θ ÷ (K (1 − θ)). With K = 0.2, q_max = 10 and q = 5, θ is 0.5 and c is 5. The amount adsorbed must be below q_max, since no pressure can fill the surface beyond a monolayer.

The Freundlich equation

For heterogeneous surfaces the Freundlich equation is x/m = K_F × c^(1/n), where x/m is the mass adsorbed per mass of adsorbent and c is the equilibrium concentration [2]. In logarithmic form it is a straight line, log(x/m) = log K_F + (1/n) log c [2]. The constants are specific to the system and temperature [2]. The page gives values from Freundlich's own work in 1907, such as K = 2.606 and n = 2.35 for acetic acid on charcoal [2]. With c = 0.5 these give an adsorbed amount of about 1.94.

Choosing a model

The page notes that the Freundlich equation is unique in form, so a good fit does not prove that the surface is heterogeneous, and that it fails at higher pressure where the surface saturates [2]. The Langmuir model saturates by design. Try both on your data and compare, then judge by the physical picture and not by the fit alone.

Reading a Langmuir plot

Plot the amount adsorbed against the concentration and the curve rises steeply and then levels off at the monolayer capacity. A larger K means that the curve rises faster, so the surface fills at a lower concentration. If you plot c divided by q against c, you get a straight line whose slope is one over q_max and whose intercept is one over K times q_max, a way to find the constants from data, though modern practice prefers a direct fit to the curve.

Uses

Adsorption isotherms describe activated carbon removing pollutants from water, gas storage in porous solids, catalysts and chromatography. The Langmuir constants tell you how strongly something binds and how much a surface can hold, which are the numbers that decide the size of a filter bed. Use the calculator to explore how the coverage changes when you vary the concentration.

Checking your inputs

Make sure the unit of K is the reciprocal of the unit of the concentration or pressure. If K is given in reciprocal bar, enter the pressure in bar, and if it is in litres per milligram, enter the concentration in milligrams per litre. A mismatch changes the coverage and the answer without any warning, so it is the first thing to check when a result looks wrong.

Common mistakes

  • Using the wrong unit for K. K has the reciprocal of the unit of c.
  • Expecting more than a monolayer. The model stops at full coverage.
  • Using Langmuir constants for Freundlich. They are different models.
  • Extrapolating Freundlich to high pressure. It fails when the surface saturates.

What next

Use this often? Add Langmuir Iso to your Home screen.

Frequently asked questions

What is a Langmuir isotherm calculator?

A tool that gives the fraction of a surface covered by adsorbate at a given pressure or concentration.

What is the Langmuir equation?

θ = K p ÷ (1 + K p), where K is the equilibrium constant and θ the fractional coverage.

What is the Freundlich equation?

x/m = K_F × c^(1/n) for adsorption on heterogeneous surfaces, with constants for each system.

What does a coverage of 0.5 mean?

Half the sites are occupied, which happens when the pressure equals 1/K.

What are the Langmuir assumptions?

A uniform surface, one molecule per site and no interactions between adsorbed molecules.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools