A ladder angle calculator helps you set a straight or extension ladder at a safe angle. Enter the height you need to reach to get the ladder length and how far to place the foot from the wall, or enter the working length to see the height, or check the angle of a ladder that is already up.
How to use the ladder angle calculator
- Choose US or metric units.
- Choose what you want.
- Enter the height, the working length or the foot distance.
- Press Calculate.
The one-quarter rule
The OSHA construction standard says that non-self-supporting ladders shall be used at an angle such that the horizontal distance from the top support to the foot of the ladder is approximately one-quarter of the working length of the ladder, which is the distance along the ladder between the foot and the top support [1]. That is the 4-to-1 rule: for every four feet of ladder length, put the foot one foot from the wall.
The angle it gives
If the foot is a quarter of the working length from the wall, the cosine of the angle with the ground is 1/4, so the angle is about 75.5 degrees, and the height reached is the length times 0.968. The standard mentions 75½ degrees in its strength test for non-self-supporting ladders, which are tested at that angle from the horizontal [1]. The angle follows from the rule and is our own calculation.
Worked examples
A ladder with a working length of 20 feet is set with its foot 5 feet from the wall and reaches 19.4 feet. To reach a support at 18 feet, the working length must be 18.6 feet and the foot 4.65 feet from the wall. A 6-metre working length puts the foot 1.5 metres from the wall and reaches 5.8 metres. A ladder 20 feet long with its foot 6 feet out has an angle of 72.5 degrees and is too shallow, because the foot is too far from the wall.
Reaching above a landing
When you climb onto a roof or a platform, the standard requires the side rails to extend at least 3 feet, or 0.9 metre, above the upper landing surface [1]. The general industry standard says the same [2]. The calculator adds this to the working length in the first mode, so the ladder must be at least that long. Where the extension is not possible, the standard asks for the ladder to be secured at its top to a rigid support that will not deflect [1].
Checking your ladder
Measure from the foot of the ladder to the wall and enter that with the working length. The calculator reports the angle and tells you whether the foot is too far out, too close or close to the rule. The standard uses the word approximately, so a small difference is fine. A foot too far out reduces the support and risks slipping, while a foot too close risks tipping backward.
What the standards do not say
The pages that we read set no maximum length or height for a portable ladder, and they do not allow a ladder to stand on boxes or barrels to gain height [2]. Rungs must be spaced between 10 and 14 inches apart [2]. Load ratings are set by the ladder, and the standard requires a ladder to carry at least four times the maximum intended load [1].
Setting up safely
Place the ladder on firm, level ground, with both side rails supported equally at the top [1]. Face the ladder and keep three points of contact while climbing. Do not stand on the top rungs. Keep clear of electrical lines. The calculator covers only the geometry, not these checks.
Special cases
The standard allows a different ratio for a job-made wooden ladder with spliced side rails, one-eighth of the working length [1]. Self-supporting stepladders open to their fixed angle and are not covered by the quarter rule. Always follow the manufacturer's label, which overrides general rules.
Planning a job
Before you start, measure the height of the point where the ladder will rest, add the extension above a landing if you will climb onto it, and choose a ladder whose working length is at least the length the calculator gives. Mark the foot distance on the ground with a tape so that you can set the ladder correctly the first time. A simple check is to stand with your toes at the foot of the ladder and hold your arms straight out, a rule of thumb that the calculator does not replace.
Why the angle matters
A ladder that is too steep can tip backward when you climb, and one that is too shallow can slide at the foot, because more of your weight pushes it outward. The one-quarter rule balances the two risks, and it is the reason that the same ratio is found in many safety rules. Always check the label on your own ladder for the maker's instructions.
Common mistakes
- Measuring the ladder length instead of the working length. The rule uses the distance from foot to support.
- Forgetting the 3 foot extension. The rails must pass the landing.
- Setting the foot by eye. Measure the distance.
- Using the rule for a stepladder. It applies to non-self-supporting ladders.
What next
Use this often? Add Ladder Angle to your Home screen.
Frequently asked questions
What is a ladder angle calculator?
A tool that gives the ladder length, the distance of its foot from the wall and its angle, using the one-quarter rule.
What is the 4-to-1 ladder rule?
Place the foot of the ladder one quarter of its working length from the wall, which gives an angle of about 75.5 degrees.
How far must a ladder extend above a roof?
At least 3 feet (0.9 metre) above the upper landing surface.
How do I find the ladder length for a height?
Divide the height by 0.968 for the working length, then add 3 feet if you climb onto a landing.
What angle should a ladder be at?
About 75.5 degrees from the ground, which is a foot distance of one quarter of the working length.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.