Saved

Press the star next to a tool's name to save it.

All my tools

J Pole Antenna Calculator

Use this J pole antenna calculator to find the long section, the quarter-wave matching section, the feed point and the spacing for a frequency, with the velocity factor.

Restored your last values ·

MHz

Enter the frequency in megahertz and choose the material. Bare copper or aluminium uses a velocity factor of 0.96. Otherwise, enter the velocity factor or the dielectric constant. You get the lengths of the long section, the matching section, the feed point and the spacing.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the frequency, then press Calculate.

See full result

A J pole antenna calculator gives the starting dimensions of a J-pole antenna for the frequency that you want: the long section, the short matching section, the feed point and the spacing between the two. Enter the frequency in megahertz and the material, and read the lengths in inches and centimetres.

How to use the J pole antenna calculator

  1. Choose US or metric units for the lengths.
  2. Enter the frequency in megahertz.
  3. Choose the material, or enter a velocity factor or a dielectric constant.
  4. Press Calculate.

What a J-pole antenna is

The Wikipedia article describes the J-pole as an end-fed, omnidirectional half-wave antenna that is matched to the feed line by a shorted quarter-wave stub [1]. Its two parallel conductors are about three quarters and one quarter of a wavelength long [1]. The shape of a letter J gives the antenna its name. It is popular with radio amateurs, because it can be made from copper pipe, wire or twin-lead, and it needs no ground plane.

How it works

A half-wave radiator fed at one end has a very high input impedance, around 1,000 to 4,000 ohms according to the Wikipedia article [1]. The quarter-wave stub transforms this down to a value that suits the feed line. The feed point is somewhere between the closed, low-impedance bottom of the stub and its open, high-impedance top [1]. In practice, builders slide the feed connection along the stub while they watch the SWR until it is at a minimum.

The wavelength

The calculator first finds the wavelength from the frequency, λ = c ÷ f, with the speed of light c = 299,792,458 metres per second [3]. At 145 megahertz, the wavelength is 2.0675 metres. Every length that follows is a fraction of this figure, so a higher frequency gives a shorter antenna. The wavelength is shown on the result, in metres, to four significant digits.

The velocity factor

Waves travel more slowly along a conductor or through an insulator than in free space, so the physical length is shortened by the velocity factor, VF, the ratio of the wave speed in the medium to the speed of light in vacuum. For a non-magnetic insulating material, VF = 1 ÷ √ε for a dielectric constant ε [2]. This tool uses 0.96 for bare copper as its default planning figure. The calculator offers three choices: bare copper or aluminium, a velocity factor that you know, or a dielectric constant, from which it finds the velocity factor. A foam-filled feeder, for example, has a different value to a bare pipe.

The four dimensions

With λ the wavelength and VF the velocity factor, the tool takes the long section as A = 0.75 × λ × VF, the short matching section as B = (λ ÷ 4) × VF, the feed point as C = (λ ÷ 50) × VF, and the spacing as D = 0.045 × λ ÷ 2. The long section is the three-quarter-wave element and B is the quarter-wave stub, in line with the proportions in the Wikipedia article [1]. The feed point and spacing formulas are the tool's own approximate rules. The calculator shows each in inches and centimetres.

The 145 megahertz example

Take the 2-metre amateur band, at 145 megahertz, with copper and VF = 0.96. The calculator gives A of 148.9 centimetres, B of 49.62, C of 3.97 and D of 4.652 centimetres. The feed point formula is approximate, which fits with the advice that it must be tuned.

Tuning on the antenna

The numbers are starting dimensions, not a finished design. Cut the elements a little long, and trim them while watching the SWR. Move the feed point along the stub to find the best match. The Wikipedia article says that the feed point is adjusted by sliding the connection of the feed line along the stub while watching the SWR [1]. It is worth keeping the spacing D the same along the whole length.

Mounting

Keep the antenna well clear of metal objects. The Wikipedia article says the design works well when no electrical connection exists between its conductors and the surrounding supports, because a grounded mast can draw current and spoil the pattern [1]. Use a plastic or wooden support. The antenna is omnidirectional, and the Wikipedia article gives an average free-space gain near 2.2 dBi, close to a dipole [1].

What the calculator leaves open

The calculator does not state where the long section is measured from, or the effect of the pipe diameter. The calculator therefore gives only the four lengths, and leaves the layout and the pipe size to you.

Units

Enter the frequency in megahertz. The lengths are in inches and centimetres, with your chosen unit first, and the wavelength is in metres. Use the same units when you cut, and measure carefully, since a few millimetres matter at 145 megahertz. The result is rounded to four significant digits. If you use a different material, such as foam-filled feeder, enter its velocity factor or its dielectric constant, and compare the lengths with those for bare copper.

Common mistakes

  • Using the length as an exact value. Trim and test with an SWR meter.
  • Forgetting the velocity factor of the material. Choose the right material.
  • Mounting it on a metal mast. Keep it clear of metal.
  • Measuring the sections from the wrong end. Check the layout before cutting.

What next

Use this often? Add J Pole Anten to your Home screen.

Frequently asked questions

What is a J pole antenna calculator?

A tool that gives the starting lengths of a J-pole antenna for a frequency and a velocity factor.

How long is a J-pole antenna?

The long section is A = 0.75 × λ × VF, which is about 148.9 cm at 145 MHz with copper.

What velocity factor does a J-pole use?

0.96 for bare copper or aluminium, or 1 ÷ √ε from the dielectric constant.

Does a J-pole need a ground plane?

No. Keep the antenna clear of metal objects and grounded masts, and mount it on a non-conducting support.

How is the feed point found?

C = (λ ÷ 50) × VF, which is 3.97 cm at 145 MHz with copper. It is approximate, so tune it while watching the SWR.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools