Saved

Press the star next to a tool's name to save it.

All my tools

Impedance Matching Calculator

Use this impedance matching calculator to find the reflection coefficient, VSWR, return loss and reflected power of a load, a quarter-wave matching section, or a conjugate match.

Restored your last values ·

Enter the line impedance and the load, as a resistance and a reactance, to get the reflection coefficient, the VSWR, the return loss and the fraction of power reflected. Or find the impedance of a quarter-wave matching section, or the load that takes the most power from a source with a reactance.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to work out, fill in the boxes, then press Calculate.

See full result

An impedance matching calculator shows how well a load is matched to a line or a source. Enter the line impedance and the load's resistance and reactance, and it gives the reflection coefficient, the VSWR, the return loss in decibels and the share of power that is reflected. It also gives the impedance of a quarter-wave matching section, and the load that takes the most power from a source.

How to use the impedance matching calculator

  1. Choose reflection and VSWR, quarter-wave transformer or conjugate match.
  2. Enter the line impedance, usually 50 or 75 ohms, and the load resistance and reactance.
  3. Press Calculate.

Matching and maximum power

The Wikipedia article on impedance matching says that for maximum power transfer the load impedance must equal the complex conjugate of the source impedance, so that the resistances are equal and the reactances are equal in size and opposite in sign.[1] For a purely resistive source and load, maximum power is transferred when the load resistance equals the source resistance.[1] A conjugate match differs from a reflectionless match, where the load equals the line impedance, when the source or the load is reactive.[1] The third mode gives the conjugate of the source you enter: for 50 + j25 ohms the load is 50 − j25 ohms.

The reflection coefficient

The article on the reflection coefficient gives the coefficient of a load as Γ = (ZL − Z0) ÷ (ZL + Z0), the ratio of the reflected to the incident voltage.[3] It says the reflected power is the incident power times |Γ| squared, and that the power delivered is 1 − |Γ| squared of the incident power.[3] For a 50 ohm line and a 200 ohm load, Γ = 150 ÷ 250 = 0.6, so 36 percent of the power is reflected and 64 percent delivered. The calculator handles a complex load with a reactance too: for 50 + j50 ohms on a 50 ohm line, |Γ| is 0.447 at 63.4 degrees.

The VSWR

The article on the standing wave ratio gives VSWR = (1 + |Γ|) ÷ (1 − |Γ|) and the reverse, |Γ| = (VSWR − 1) ÷ (VSWR + 1).[4] For a resistive load it is the larger of RL ÷ Z0 and Z0 ÷ RL.[4] The page's examples show that Γ = 0.6 gives a VSWR of 4, and Γ = −0.333 gives 2.[4] Enter 200 ohms on a 50 ohm line to get 4, and 25 ohms to get 2. A perfect match has a VSWR of 1.

Return loss and mismatch loss

The pages we read give no formulas for return loss or mismatch loss, so these two figures are our own working. The return loss in decibels is −20 times the base 10 logarithm of |Γ|, and the mismatch loss is −10 times the logarithm of 1 − |Γ| squared, the power lost to reflection. For a VSWR of 2, |Γ| = 1/3, the return loss is 9.54 dB and the mismatch loss is 0.51 dB. A perfect match has an infinite return loss and no mismatch loss.

The quarter-wave transformer

The article on the quarter-wave impedance transformer gives the input impedance of a lossless line and says that at a quarter of a wavelength it is Zin = Z0 squared divided by ZL.[2] Solving for the section that matches a source of impedance Rs to a load RL gives Z0 = √(Rs × RL), which is our own algebra. To match 50 ohms to 200 ohms, use a quarter-wave line of 100 ohms. Then Zin = 100² ÷ 200 = 50 ohms, as the calculator checks. The page says that the transformer is suitable only for a narrow band, because the line is a quarter wavelength at one frequency, and that the analysis assumes no appreciable loss along the line.[2]

Matching at one frequency

The page on impedance matching says that matching is done over a specified frequency band, that perfect matching at all frequencies is not possible with discrete networks, and that a single reactance can match at only one frequency.[1] It adds that matching strictly applies to linear devices.[1] So treat the results as correct at the frequency for which the impedances were measured.

Worked examples

A 75 ohm antenna on a 50 ohm line gives Γ = 25 ÷ 125 = 0.2, a VSWR of 1.5, 4 percent of the power reflected and a return loss of 14 dB. A 300 ohm twin-lead matched to 75 ohm coax needs an impedance ratio of 4, which the page says is done with a 2 to 1 turns ratio, the square root of the ratio.[1] A 75 ohm to 300 ohm quarter-wave section is 150 ohms. The first and last are our own calculations.

Reading the VSWR in practice

The page says the standing wave ratio of a lossless line is the same at any point along it, and that a meter is valid only for the impedance that it is designed for, usually 50 or 75 ohms.{4} It also says the losses of a line always increase with frequency, so the loss of a mismatched line grows at higher frequencies; for a 6 to 1 ratio on 75 metres of RG-8A cable, its example gives 2.2 dB of loss at 3.5 MHz and 10.8 dB at 146 MHz.{4} This is why a mismatch that is harmless on a short low-frequency run may be costly on a long run at a high frequency.

Choosing a matching method

Use a quarter-wave section when you need a narrow-band match between two resistive impedances and can make a line of the right length. Use a transformer for a wide band between impedances that differ by a fixed ratio, and use reactive components when you have a source with reactance. The calculator gives the first and the conjugate; for the others, use a network design tool. This advice is general practice and not from the pages that we read.

Common mistakes

  • Ignoring the reactance. A load with reactance reflects more than its resistance alone suggests.
  • Using the wrong line impedance. VSWR is relative to the line you use.
  • Expecting a wide band. A quarter-wave section matches only near one frequency.

What next

Use this often? Add Impedance Ma to your Home screen.

Frequently asked questions

What is an impedance matching calculator?

A tool that shows how well a load matches a line or source, giving the reflection coefficient, VSWR, return loss and the power reflected.

What is the formula for the reflection coefficient?

Γ = (ZL − Z0) ÷ (ZL + Z0), where ZL is the load and Z0 the line impedance.

What is the formula for VSWR?

VSWR = (1 + |Γ|) ÷ (1 − |Γ|). For a resistive load it is the larger of RL ÷ Z0 and Z0 ÷ RL.

How do I match two resistances with a quarter-wave line?

Use a line of impedance √(Rs × RL), a quarter wavelength long. Matching 50 to 200 ohms needs 100 ohms.

When is power transfer greatest?

When the load impedance is the complex conjugate of the source impedance, or equal to the source resistance for resistive sources.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools