Saved

Press the star next to a tool's name to save it.

All my tools

Hydraulic Pressure Calculator

Use this hydraulic pressure calculator to find the force, pressure or bore of a hydraulic or pneumatic cylinder, or the force ratio of a two-piston lift, in US or metric units.

Restored your last values ·

Pick what you want to find. For a single cylinder, enter two of pressure, bore and force. For a two-piston hydraulic jack, enter the load, the effort piston and the load piston. Choose US or metric units first.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find, fill in the boxes that appear and press Calculate.

See full result

A hydraulic pressure calculator links the three numbers that describe a cylinder: the fluid pressure, the piston area from its bore, and the force. Enter two and it finds the third, or it works out a two-piston hydraulic lift from Pascal's law. The same maths also covers piston force and pneumatic cylinder force, as the working is identical.

How to use the hydraulic pressure calculator

  1. Choose US or metric units.
  2. Pick what to find: the force, the pressure, the bore size or a two-piston lift.
  3. Fill in the boxes that appear. The placeholder shows an example value.
  4. Press Calculate and read the result, the working and, for a lift, the force ratio.

Pascal's law in plain words

In a closed fluid at rest, a pressure applied at one point is transmitted equally and undiminished to all points of the fluid [1]. Two pistons joined by the same liquid therefore feel the same pressure. It is the pressures, not the forces, that are equal in the two cylinders. Since pressure is force divided by area, p = F ÷ A [3], a small force on a small piston balances a large force on a large piston, which is why a hydraulic jack can raise a car.

The force ratio of two pistons

Equal pressure means F₁ ÷ A₁ = F₂ ÷ A₂, or F₂ ÷ F₁ = A₂ ÷ A₁ [1]. The ratio of the forces is the ratio of the piston areas. A load piston ten times wider than the effort piston has one hundred times the area, so it lifts one hundred times the effort force. The calculator shows this ratio in the lift mode, so that you can see the gain in force at a glance.

Force from pressure and bore

For one cylinder, the force is the pressure times the area of the piston face: F = P × A [2]. For a round piston the bore area is A = π × d² ÷ 4. For example, a 25 mm bore at 100 kPa gives a force of about 49.09 newtons. The calculator gives the same figure in the force mode, 49.087 N, and shows it in pounds-force as well.

Pressure and bore from the force

The same formula can be turned round. To find the pressure needed to push with a given force on a known bore, use P = 4F ÷ (π d²). For example, 500 N on a 25 mm bore needs about 1,018.6 kPa. To find the bore for a given force and pressure, the calculator finds the area F ÷ P first and then the diameter.

A worked two-piston lift

Take a jack with a 3 cm effort piston and a 30 cm load piston lifting a car of 1,000 kg. The load force is 1,000 × 9.80665 = 9,806.65 N. The areas are in the ratio of 100 to 1, so the effort force is 98.07 N, and the fluid pressure is about 138.74 kPa.

Distance and work

A hydraulic lift does not create energy. The work done by the effort, force times distance, equals the work done on the load [1]. Since the effort force is smaller, the effort piston has to move farther: d₁ = (A₂ ÷ A₁) × d₂, where d₂ is how far the load rises. With an area ratio of 100, you must pump the small piston 100 times as far as the load goes up. The calculator states this travel ratio with every lift result.

Piston force and pneumatic cylinders

The same principle applies to pneumatic cylinders, with compressed air in place of oil. For an air cylinder, enter the gauge pressure of the supply as the pressure and the bore of the cylinder. The result is the theoretical push on the piston. The tool takes the pressure as gauge pressure, so check this before using any result, and remember that a real air cylinder delivers less than the theoretical force.

US and metric units

In US mode, enter the pressure in psi, the diameters in inches and the force in pounds-force. In metric mode, enter kPa, millimetres and newtons. The calculator converts to SI units, works out the answer and shows both systems. The conversion factors, 6,894.757 pascals per psi, 0.0254 metres per inch and 4.44822 newtons per pound-force, are standard values of our own, not taken from the pages cited.

What the calculation leaves out

The result is an ideal figure. Friction between the piston and the seals, back pressure on the other side of the piston, the compressibility of the fluid and the weight of the fluid column are all ignored. The tool uses the full bore area and does not cover the rod side of a double-acting cylinder, where the rod reduces the area and the force available for retraction [2]. Friction in the seals and mounting bushings can make the measured force differ from the calculated force by 20% or more [2]. Real cylinders also have an efficiency of less than one, so allow a margin.

Safety

A pressurised system can injure or kill if a hose, fitting or seal fails, and a raised load can fall. Use the figures from this page only for study and first estimates. Check pressure ratings, relief valves, load supports and the standards for your equipment with a qualified engineer before building a lifting or pressing system.

Common mistakes

  • Using the same units for every box. Pick US or metric once, and enter every value in that system.
  • Confusing diameter with radius. The boxes ask for the diameter of the bore, not the radius.
  • Mixing gauge and absolute pressure. Use the gauge pressure unless you know the source gives the absolute pressure.
  • Expecting the full theoretical force. Friction and seals take part of it.

What next

Use this often? Add Hydraulic Pr to your Home screen.

Frequently asked questions

What is a hydraulic pressure calculator?

A tool that links the pressure, the piston area and the force in a hydraulic or pneumatic cylinder, and works out two-piston lifts.

What is the formula for piston force?

F = P × A, where A = π d² ÷ 4 is the area of the bore.

How does Pascal's law work in a hydraulic jack?

The pressure is the same on both pistons, so F₁ ÷ A₁ = F₂ ÷ A₂.

Does the calculator work for a pneumatic cylinder?

Yes, enter the gauge air pressure and the bore. The result is the theoretical force before losses.

Why must the small piston move farther?

Work is conserved, so a smaller force acts over a longer distance.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters