Saved

Press the star next to a tool's name to save it.

All my tools

Henderson Hasselbalch Calculator

Use this Henderson Hasselbalch calculator to find the pH of a buffer, the base to acid ratio for a target pH, convert Ka and pKa, and estimate the effect of adding strong acid or base.

Restored your last values ·

Choose a job. Enter the pKa and the concentrations of the acid and base forms to get the pH of the buffer. You can also find the ratio for a target pH, convert between Ka and pKa, see how a little strong acid or base changes the pH, and estimate the buffer capacity.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what you want and fill in the boxes, then press Calculate.

See full result

The Henderson Hasselbalch calculator gives the pH of a buffer made from a weak acid and its conjugate base, finds the ratio of base to acid that gives a target pH, converts between Ka and pKa, and shows how adding a little strong acid or base moves the pH. It also estimates the buffer capacity. Choose a job, enter the numbers and press the button.

How to use the Henderson Hasselbalch calculator

  1. Choose what you want.
  2. Enter the pKa and the concentrations of the acid and base forms, or the target pH.
  3. For a change, enter the strong acid (positive) or base (negative) that you add.
  4. Press Calculate.

The equation

The Henderson-Hasselbalch equation says that pH = pKa + log₁₀ of the concentration of the base divided by the concentration of the acid [1]. It follows from the definition of the acid dissociation constant, Ka = [H⁺][A⁻]/[HA], and pKa is minus the base 10 logarithm of Ka [3]. When the acid and base are present in equal amounts, the logarithm is zero and the pH equals the pKa. For acetic acid, with Ka = 1.8 × 10⁻⁵, the pKa is about 4.7 [3].

Worked example

A buffer of 0.1 mol/L acetic acid and 0.2 mol/L acetate with a pKa of 4.76 has a pH of 4.76 plus log₁₀ 2, which is 5.06. A ratio of 10 to 1 in favour of the base gives a pH one unit above the pKa, 5.76. The calculator shows what share of the buffer is in each form: at a ratio of 10, 90.9 percent is in the base form. The pKa of 4.76 for acetic acid is a common textbook value, and the page that we read gives it as 4.7 or 4.8, so check your source.

Choosing a buffer

A buffer works best close to its pKa. The page on buffer solutions gives the useful range as about pKa ± 1 and advises choosing a buffer with a pKa as close as possible to the target pH [2]. Its table lists acetic acid with a pKa of 4.7 and a range of 3.8 to 5.8, potassium dihydrogen phosphate with 7.2 and a range of 6.2 to 8.2, and borate with 9.24 and a range of 8.25 to 10.25 [2]. Blood is buffered at a pH of 7.40, give or take 0.05 [2]. The calculator prints the range around your pKa.

Adding strong acid or base

Strong acid added to a buffer turns some of the base form into the acid form, and strong base does the reverse. The pH then follows from the new concentrations. Adding 0.01 mol/L of strong acid to a buffer of 0.1 and 0.1 mol/L lowers the pH from 4.76 to 4.67. The calculator ignores the small dilution from the added liquid and refuses an addition that would use up the buffer. The page uses a more exact method for a solution of the acid alone, with the equation Ka = x(x + y)/(C₀ − x) [2], which the pH mode here does not need.

Buffer capacity

Buffer capacity is the amount of strong acid or base that changes the pH by one unit, per litre of buffer, β = dn/dpH [2]. The page gives it near the pKa as 2.303 times the total buffer concentration times Ka times [H⁺], divided by (Ka + [H⁺]) squared [2]. It is greatest when the pH equals the pKa, where it is 2.303 times the concentration divided by 4, and it falls to a third of that value at pKa ± 1, to 10 percent at ± 1.5 and to 1 percent at ± 2 [2]. For a 0.2 mol/L buffer the peak is 0.115 mol/L per pH unit. This form leaves out the terms for water and for very strong acids and bases.

Limits

The page says that the equation applies to a polyprotic acid only when consecutive pKa values differ by at least 3 [1]. It assumes that the salt is completely dissociated and that activity coefficients are constant [2]. At high concentrations or ionic strengths the true pH differs. Water's own ionization is ignored, which is not strictly valid near pH 7.

Bases

The same equation works for a weak base if you use the pKa of its conjugate acid. The pKa of the conjugate acid is the pKw minus the pKb, with the pKw about 14 at 25 °C [3]. Enter that pKa and the concentrations of the base and its conjugate acid, with the base in the base box.

Making a buffer

To make a buffer of a chosen pH, pick an acid with a pKa within one unit of the target, then use the ratio mode to find the base to acid ratio. Weigh out the acid and its salt in that ratio and dissolve them in water, or start with the acid and add strong base until the ratio is right. Check the pH with a meter and adjust, because activity effects and temperature change the result. A higher total concentration gives more capacity.

Common mistakes

  • Putting the ratio upside down. The ratio is the base over the acid.
  • Using a buffer far from its pKa. Choose a buffer within one unit of the target.
  • Mixing Ka and pKa. pKa is the negative logarithm of Ka.
  • Ignoring concentration. A dilute buffer has little capacity.

What next

Use this often? Add Henderson Ha to your Home screen.

Frequently asked questions

What is a Henderson Hasselbalch calculator?

A tool that uses pH = pKa + log([base] ÷ [acid]) to find the pH of a buffer or the ratio of base to acid for a target pH.

What is the Henderson-Hasselbalch equation?

pH = pKa + log₁₀([A⁻] ÷ [HA]). When the two forms are equal, the pH equals the pKa.

What is the useful range of a buffer?

About pKa ± 1. Acetic acid, with a pKa near 4.7, buffers from about 3.8 to 5.8.

How do I convert pKa to Ka?

Ka = 10 raised to the power of minus pKa. A pKa of 4.76 is a Ka of about 1.74 × 10⁻⁵.

What is buffer capacity?

The amount of strong acid or base that changes the pH by one unit in a litre of buffer. It is greatest when the pH equals the pKa.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools