Saved

Press the star next to a tool's name to save it.

All my tools

Helical Coil Calculator

Use this helical coil calculator to find the wire length, the coil height and the wire volume from the coil diameter, wire diameter, number of turns and spacing.

Restored your last values ·

turns

Enter the coil diameter, the wire diameter, the number of turns and the gap between turns. You get the length of wire needed, the height of the coil and the volume of the wire.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the coil diameter, the wire diameter and the number of turns, then press Calculate.

See full result

A helical coil calculator finds how much wire you need to wind a coil, how tall the coil is and how much material the wire contains. Enter the coil diameter, the wire diameter, the number of turns and the spacing between the turns. Choose US inches or metric millimetres.

How to use the helical coil calculator

  1. Choose US (inches) or Metric (millimetres).
  2. Enter the coil diameter, the wire diameter and the number of turns.
  3. Add the spacing between turns if they do not touch, then press Calculate.

The formulas

The height of the coil is H = N (S + Dw), the number of turns times the pitch [1]. The wire length is N × √((π Dc)² + (S + Dw)²), and the wire volume is π Dw² × length ÷ 4, the volume of a cylinder of wire [2]. Here N is the number of turns, S the spacing, Dw the wire diameter and Dc the coil diameter. The calculator uses these three formulas. It also shows the pitch, the length per turn and the outside diameter, which are our own working.

Why the length uses a square root

Wikipedia gives the length of one turn of a helix as the square root of (2π a)² plus the pitch squared, where a is the radius and the pitch is the height gained in one turn [1]. With a = Dc ÷ 2 the first term is (π Dc)². The pitch of a coil is the wire diameter plus the spacing, S + Dw. So one turn is a slanted line, and N turns give N times its length.

A worked example

Take a coil with a diameter of 10 mm, wire of 0.5 mm, 15 turns and a spacing of 0.3 mm. The pitch is 0.8 mm, so the height is 15 × 0.8 = 12 mm. One turn uses 31.426 mm of wire, so 15 turns use 471.39 mm. The volume is 92.558 mm³. Rounded, that is 12 mm, 471.4 mm and 92.56 mm³.

What the diameter means

The coil diameter in the formula is the diameter of the circle that the centre of the wire follows. If you measure across the outside of the winding, subtract one wire diameter. The calculator shows the outside diameter, Dc + Dw, for a check. For a coil wound on a rod, the coil diameter is the rod diameter plus one wire diameter. Getting this right matters because the wire length depends on it directly.

Spacing and tight coils

If the turns touch, leave the spacing blank or enter zero. The pitch is then the wire diameter, and the coil is as short as possible. Adding spacing makes the coil taller and uses a little more wire per turn, but does not change the diameter. The height formula counts N pitches, so the real outer height of a coil is a little smaller, by the spacing, since the last gap is not part of the coil.

Units

In US mode, lengths are in inches, the wire length is also shown in feet, and the volume is in cubic inches. In metric mode, lengths are in millimetres, the wire length is also shown in metres, and the volume is in cubic millimetres. The logic is the same in both, so you can check a design in either system. A US example with a 0.4 inch coil and 0.02 inch wire gives 18.856 inches of wire for 15 turns and a 0.012 inch spacing.

Wire volume and weight

The volume of the wire is the area of its circular cross-section, π Dw² ÷ 4, times its length [2]. Multiply the volume by the density of the metal to get the mass. For example, copper is much denser than aluminium, so the same coil weighs more in copper. The calculator gives only the volume, because the density depends on the material and the alloy you use.

Inductance is not included

We did not include the inductance of the coil, because it depends on the winding, the core and the way the coil is built. This tool covers the geometry only: height, wire length and wire volume.

Using the calculator

Start with your coil diameter and wire size, then change the number of turns to see how the wire length grows in a straight line with N. Add extra for the two ends where the wire leaves the coil. Buy a little more wire than the result to allow for cutting and for bending the wire tightly around a former or mandrel.

Practical winding tips

Wind the coil on a former whose diameter equals the coil diameter minus one wire diameter, so the wire centre line follows the circle that the formula expects. Keep the tension even, and use a spacer of known thickness if you want a fixed gap between turns. After winding, the coil usually springs open a little, so the finished diameter may be slightly larger than the former. Always add some extra wire for the leads, and cut it only after you have checked the length against the result. The calculator treats the ends as part of the turns.

Common mistakes

  • Measuring the diameter to the outside of the wire. Use the centre line, or subtract one wire diameter.
  • Forgetting the extra wire for the leads. Add it yourself.
  • Mixing inches and millimetres. Pick one system.
  • Using a wire diameter that includes insulation. Use the diameter that determines the spacing.

What next

Use this often? Add Helical Coil to your Home screen.

Frequently asked questions

What is a helical coil calculator?

A tool that finds the wire length, the height and the wire volume of a coil from its size and number of turns.

How do I find the wire length of a coil?

Multiply the number of turns by the square root of (π × coil diameter) squared plus the pitch squared.

What is the pitch of a coil?

The wire diameter plus the spacing between turns: the height gained in one turn.

How do I find the height of a coil?

H = N × (S + Dw), the number of turns times the pitch.

Does it calculate the inductance?

No. Inductance depends on the winding and the core, so only the geometry is covered.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Math Tools