A hammock hang calculator often sizes a whole setup: strap height, hammock length and tree spacing. This one does a narrower job. It finds the pull in each cord from the hanging weight and the angle that the cord makes with the horizontal. It is a physics check and not a safety rating.
How to use the hammock hang calculator
- Choose US or metric units.
- Enter the hanging weight, which is you plus anything in the hammock.
- Enter the cord angle from horizontal in degrees.
- Press Calculate, and read the warning first.
What this calculator does and does not do
The inputs are the hanging weight and the cord angle, and the setup is treated as a static load, which means nothing is accelerating. This tool is deliberately small. It works out the pull in each cord and nothing else: no hammock length, no anchor height and no ridgeline. The sources we opened give the general method of statics but no hammock-specific formula, so every number here is our own working from that method [1].
The formula
Each of the two cords carries half of the weight in the vertical direction, W ÷ 2. A cord that makes an angle θ with the horizontal has a vertical part T sin θ, so T sin θ = W ÷ 2 and the pull is T = W ÷ (2 sin θ). The horizontal part is T cos θ, which equals (W ÷ 2) ÷ tan θ. This is the resolution of forces from basic statics: the tensions are split into vertical and horizontal parts, and the vertical parts must add up to the weight because the net force along each axis is zero [1]. The cord formula itself is our own working.
A worked example
Take 175 pounds hanging at 30 degrees from horizontal. Half of the weight is 87.5 pounds on each side. Since sin 30 degrees is 0.5, the pull in each cord is 87.5 ÷ 0.5 = 175 pounds, the same as the whole weight. The horizontal part is 87.5 ÷ tan 30 degrees = 151.55 pounds, which pulls the two anchors toward each other.
Why a flatter hang pulls harder
As the angle gets smaller, sin θ gets smaller and the pull grows quickly. For the same 175 pounds, the cord pull is 503.89 pounds at 10 degrees, 255.83 pounds at 20 degrees, 175 pounds at 30 degrees and 123.74 pounds at 45 degrees. A cord pulled almost straight carries much more load than the same cord with a deeper sag, and a perfectly straight cord would need an unlimited pull. The calculator lists this comparison with every result.
Metric units
In metric mode, enter the weight in kilograms. The result is shown in kilograms-force and in newtons, using 9.80665 newtons per kilogram-force, from the standard value of gravity of 9.80665 meters per second squared [2]. For 80 kilograms at 15 degrees, the pull in each cord is 154.55 kilograms-force, or 1,515.6 newtons. The vertical part is 40 kilograms-force, half of the weight, and the logic is the same as in the US mode.
The angle you enter
Enter the angle between the cord and a horizontal line. Hammock guides do not all measure the angle in the same way, so check which one you mean before you compare numbers from different pages. The calculator accepts any angle above 0 and below 90 degrees. Very small angles give very large pulls, which is the physics and not an error.
Read the safety warning
The result is not a rating. It does not include a safety factor, and it does not include the extra load from getting in, sitting down, swinging or sharing the hammock. Physics gives a load and not a verdict, so the tool gives no safe or unsafe answer either. Compare the figure with the rated working load printed on your straps, carabiners, hardware and hammock, and with the capacity of your anchors. If you are not sure, ask the maker of the gear or a qualified person.
What the calculator assumes
It assumes the object is in equilibrium, which means the resultant force is zero [3], with two cords at the same angle, with both anchors at the same height, and a weight that hangs in the middle. It treats the hammock and the cords as weightless and does not allow for stretch. The result is a clean starting figure for a simple, still hang.
What it leaves out on purpose
A full hammock plan also involves values such as hammock length, anchor height and the length of the suspension. None of the sources we opened gives equations for them, so we left those out and kept only the one result that comes from statics. If you need a complete setup, use the guidance of the hammock maker.
Using the results
Use the table of other angles to see how much a small change matters. Then use the manufacturer's ratings, not this page, to decide whether a setup is suitable.
Why there is no safety factor
A safety factor is a margin between the load that a piece of gear will carry and the load you put on it. We have no source for a figure that suits hammocks, so the tool does not invent one. The gear itself carries the information that matters: look for the rated working load on the label or in the instructions, and compare it with the larger of the numbers shown here, plus a generous allowance for movement.
Checking the numbers yourself
You can test the tool by hand. With 175 pounds at 30 degrees, half the weight is 87.5 pounds, and dividing by 0.5 gives 175 pounds. Repeat with 20 degrees and you should find 255.83 pounds.
Common mistakes
- Treating the result as a safe load. It is not a rating or a limit.
- Leaving out the load that you carry. Add gear and any second person to the weight.
- Measuring the angle from the tree. Use the angle from horizontal.
- Ignoring movement. Swinging and sitting down add to the pull.
What next
Use this often? Add Hammock Hang to your Home screen.
Frequently asked questions
What is a hammock hang calculator?
A tool that works out hammock setups. This one finds the pull in each cord from the hanging weight and the cord angle.
What is the formula for the pull in each cord?
T = W ÷ (2 sin θ), where W is the hanging weight and θ is the cord angle from horizontal. This is our own working from statics.
Does the calculator say if my hammock hang is safe?
No. It gives no safe or unsafe verdict. Check the ratings of your anchors, straps, hardware and hammock, and ask a qualified person if you are unsure.
Why does the pull grow when the angle gets smaller?
The cords carry the weight only through their vertical part. A flatter cord has a smaller vertical part for the same pull, so the pull has to rise.
Why does it not give the hammock length or anchor height?
The sources we opened give no equations for them, so we kept only the cord pull, which follows from statics.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.