Saved

Press the star next to a tool's name to save it.

All my tools

Hall Coefficient Calculator

Use this Hall coefficient calculator to find the Hall coefficient and carrier concentration, or solve for the Hall voltage or the magnetic field, from R_H = V t ÷ (I B).

Restored your last values ·

mV
mm
A
T
mm³/C
per m³

Choose what to find. For the Hall coefficient, enter the Hall voltage in millivolts, the thickness in millimetres, the current in amperes and the magnetic field in teslas. The other modes solve the same relation for the voltage or the field, or give the coefficient from a carrier concentration.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find, fill in the other values, then press Calculate.

See full result

A Hall coefficient calculator uses the Hall effect: a voltage appears across a conductor that carries a current in a magnetic field. Enter the voltage, thickness, current and field to find the Hall coefficient and the carrier concentration, or solve for the voltage or the field.

How to use the Hall coefficient calculator

  1. Choose what to find.
  2. Enter the other values: voltage in millivolts, thickness in millimetres, current in amperes, field in teslas.
  3. Press Calculate.

The Hall effect

When a current flows along a conductor in a magnetic field at right angles to it, a voltage appears across the conductor. Wikipedia defines a material and temperature dependent Hall coefficient R_H through E_y = R_H j_x B_z, the sideways electric field in terms of the current density and the field [1]. The same article says the coefficient is tied to the type, number and properties of the charge carriers [1], so it reveals their nature, their concentration and their charge.

The coefficient

Wikipedia gives the Hall voltage as V = R_H I B ÷ d, with d the thickness [1]. Solving for the coefficient gives R_H = V t ÷ (I B), where V is the observed voltage, t is the thickness of the conductor (d above), I the current and B the magnetic field. R_H comes out in cubic metres per coulomb. Our tool takes V in millivolts and t in millimetres, and it shows the result in mm³/C and in m³/C. One mm³/C is 10⁻⁹ m³/C.

Worked example

Take an illustrative R_H = 0.133 mm³/C, a plate 0.02 mm thick, a current of 10 A and a voltage of 0.05 mV. Solving B = V t ÷ (I R_H) gives 0.7519 tesla. This is our own working, and 0.133 mm³/C is an example value, not a measured figure for a named metal. Choose the field mode and enter those numbers: the tool gives 0.7519 T. Back in the coefficient mode, 0.05, 0.02, 10 and 0.7519 give 0.133 mm³/C, 1.33 × 10⁻¹⁰ m³/C.

Hall voltage

The Hall voltage is V = R_H I B ÷ t. Wikipedia writes the same relation, with the Hall voltage in terms of R_H, the current, the field and the thickness [1]. With the example values above, the tool gives 0.05 mV.

Carrier concentration

HyperPhysics gives the Hall voltage in terms of the carrier density n and the electron charge e as V = I B ÷ (n e d) [3]. Setting that equal to R_H I B ÷ d gives |R_H| = 1 ÷ (n e). For one kind of carrier, our tool takes the size of the concentration as n = 1 ÷ (|R_H| e), with e = 1.602176634 × 10⁻¹⁹ C, the exact value given by Wikipedia [2]. For R_H = 0.133 mm³/C, this is about 4.69 × 10²⁸ per cubic metre. This step is our own working from the page's relation.

Sign of the coefficient

Wikipedia states that if holes are dominant, the Hall voltage is positive, and if electrons are dominant, it is negative [1]. The tool follows this: a negative R_H means negative carriers, electrons, and a positive one means positive carriers, holes. Its result lines state which one dominates, and say that the concentration holds if one kind of carrier carries the current. The elementary charge is shown as −e for the electron in Wikipedia's table [2].

From concentration to coefficient

In the last mode, you give the carrier concentration and the type of carrier, and get R_H = ±1 ÷ (n e): minus for electrons, plus for holes. If you also enter the thickness, current and field, the tool adds the Hall voltage. With 4.6929e28 electrons per cubic metre, the coefficient is −0.133 mm³/C, and with the example numbers the voltage is −0.05 mV.

Choosing a coefficient

The 0.133 mm³/C in the examples is only an illustration. A positive sign would mean hole-like carriers, which is unusual for a metal. The calculator uses whatever coefficient you enter, so take the value for your material from a data table before using the result for anything more than practice.

Units

Voltage is in millivolts, thickness in millimetres, current in amperes, field in teslas and the coefficient in mm³/C, convenient units for a thin plate. The conversions are exact powers of ten: one millivolt is 10⁻³ volt, one millimetre is 10⁻³ metre. The tool does not need a US and metric choice, since it works with these science units only. Carrier concentrations are shown per m³ and per cm³.

Limits

The formulas treat a single kind of carrier and a uniform field and current in a thin plate. Semiconductors often have both electrons and holes, and the measured coefficient is then a mix. A real Hall measurement also has to deal with misalignment voltages. Use the calculator for the idealised relation, to check a lab report or to see how the voltage scales with the current and the field.

How the voltage scales

Our own reading of V = R_H I B ÷ t is useful when planning a measurement. The voltage grows in proportion to the current and to the field, so doubling either doubles the voltage. It falls as the plate gets thicker, so halving the thickness doubles the voltage. That is why Hall measurements use thin plates and strong currents, as long as the plate does not overheat. Try different values in the voltage mode to see this.

Common mistakes

  • Entering the thickness in the wrong direction. Use the thickness along the magnetic field.
  • Mixing millivolts and volts. The voltage box is in millivolts.
  • Entering zero for the current or the field. They divide the formula.
  • Ignoring the sign. It tells you the carrier type.

What next

Use this often? Add Hall Coeffic to your Home screen.

Frequently asked questions

What is a Hall coefficient calculator?

A tool that finds the Hall coefficient from the voltage, thickness, current and magnetic field, and also solves for the voltage or the field.

What is the Hall coefficient formula?

R_H = V t ÷ (I B), with R_H in cubic metres per coulomb.

What does the sign of R_H tell me?

A negative value means electrons dominate and a positive value means holes dominate.

How is the carrier concentration found?

n = 1 ÷ (|R_H| e) for one kind of carrier, with e the elementary charge.

Which units does the tool use?

Millivolts, millimetres, amperes, teslas and mm³/C, with the coefficient also shown in m³/C.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools