Saved

Press the star next to a tool's name to save it.

All my tools

Fuel Injector Calculator

Use this fuel injector calculator to size injectors from horsepower, BSFC, the number of injectors and duty cycle, in lb/h and kg/h.

Restored your last values ·

%

Enter the power you want, the engine's BSFC, the number of injectors and the duty cycle you are willing to use at full power. A duty cycle below 100 percent leaves headroom.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter a value and press Calculate.

See full result

A fuel injector calculator estimates how large each injector must be to feed an engine at its target power. Enter the horsepower, the engine's brake specific fuel consumption, the number of injectors and the duty cycle you want at full power, and the calculator shows the flow each injector needs, in pounds and kilograms per hour.

How injector size is worked out

The fuel an engine burns is its power times its BSFC. Wikipedia defines BSFC as the rate of fuel consumption divided by the power produced, so fuel flow is power multiplied by BSFC. That fuel is shared between the injectors, and each one can only flow while it is open, so the size is divided by the duty cycle, which is the fraction of the time the injector is open.

Total fuel flow (lb/h) = horsepower × BSFC (lb/hp·h)
Injector size (lb/h) = horsepower × BSFC ÷ (number of injectors × duty cycle)

How to use the fuel injector calculator

  1. Enter the engine power in horsepower that you want to support.
  2. Enter the BSFC in lb/hp·h. For a gasoline engine, Wikipedia gives a cycle average of 322 g/kWh, which is about 0.53 lb/hp·h, and a best figure near 225 g/kWh, about 0.37.
  3. Enter the number of injectors, usually one per cylinder.
  4. Enter the duty cycle you will allow at full power, such as 80 percent.
  5. Press Calculate to see the size for each injector.

Worked example

An eight-cylinder engine is to make 300 hp with a BSFC of 0.5 lb/hp·h. Total fuel flow is 300 × 0.5 = 150 lb/h. With eight injectors at an 80 percent duty cycle, each injector must flow 150 ÷ (8 × 0.8) = 23.4 lb/h. At 100 percent duty it would be 18.75 lb/h, but an injector held open all the time has no headroom left.

Why the duty cycle matters

An injector is a valve that opens and closes many times a second. The duty cycle is the share of each cycle it is open. At 100 percent it never closes, which leaves no room for the control system to adjust the fuel, and the injector can run hot. Sizing the injectors for a lower duty cycle at full power gives headroom for changes in fuel pressure, temperature and tuning. The right figure depends on the injector and the engine, so follow the maker's advice.

Choosing a BSFC value

The BSFC changes with speed and load, and it is higher when an engine makes more power from boost or a richer mixture. Wikipedia's figures for gasoline engines range from 225 to 322 g/kWh. For a boosted engine at full power, designers often use a higher number to be safe, so choose a value with some margin. You can work out your own number if you have a fuel flow and a power figure.

Metric units

The calculator also shows the injector size in kilograms per hour, and the BSFC in grams per kilowatt-hour using the factor 608.277. For horsepower and kilowatts, see the power converter, and for torque and power see the torque to horsepower calculator.

How the fuel injector calculator works

The calculator multiplies the horsepower by the BSFC to find the total fuel flow in pounds per hour, divides it by the number of injectors to find the share for each one, and divides again by the duty cycle as a fraction. It also shows the answer in kilograms per hour and converts your BSFC to grams per kilowatt-hour with the factor 608.277, so that you can compare it with published figures.

Choosing the injector from the result

Injectors are sold with a flow rating at a stated fuel pressure, usually in pounds per hour or cubic centimetres per minute. Pick one whose rating is equal to or above the result. If the rating is given in different units, convert it before you compare. Remember that the flow of an injector changes with the fuel pressure, so check the rating at the pressure your system uses and consider the rise in pressure for a boosted engine.

Port injection and direct injection

The calculation is the same for any number of injectors, but the way the fuel is delivered differs. A port injection engine has one injector per cylinder, and some engines have two, which halves the size each one needs. A direct injection engine has its own requirements, so use the engine maker's data. Enter the number of injectors that deliver fuel at the same time to get a result that matches your setup.

Safety and checks

Fuel systems are under pressure and the fuel is flammable, so work in a ventilated place, away from sparks, and follow the instructions for your vehicle. After fitting new injectors, have the engine tuned so that the fuel map matches the injector data. An injector that is too large can make idling rough, and one that is too small can run out of fuel at high power, which can damage an engine. The calculator gives you the starting point, and a proper tune confirms it.

Common mistakes

  • Using wheel horsepower. BSFC is based on the power at the crankshaft.
  • Forgetting the duty cycle. Without it, the injectors will be too small.
  • Counting the wrong number of injectors. Use the number that flow at the same time.
  • Mixing fuels. Fuel types differ, so check the injector's rating for the fuel you use.

What next

Use this often? Add Fuel Injecto to your Home screen.

Frequently asked questions

How does a fuel injector calculator work?

It multiplies the horsepower by the BSFC to get total fuel flow, then divides by the number of injectors and the duty cycle to give the size of each one.

What is the formula for injector size?

Injector size in lb/h equals horsepower times BSFC divided by the number of injectors times the duty cycle. For 300 hp, 0.5 BSFC, 8 injectors and 80 percent that is 23.4 lb/h.

What BSFC should I use?

Wikipedia gives 322 g/kWh as a cycle average for a gasoline engine, about 0.53 lb/hp·h, and about 225 g/kWh at best. Boosted engines at full power often need a higher figure.

What is injector duty cycle?

It is the share of the time an injector is open. At 100 percent it never closes, so sizing for a lower figure gives headroom.

Does the calculator work for diesel?

The calculation is the same, but diesel injectors are different, so use the engine maker's data. Enter a diesel BSFC if you have one.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools