The French drain calculator works out the materials for a French drain: a gravel-filled trench with a perforated pipe that carries groundwater away from a wet spot or a foundation. Enter the trench’s length, width and depth, and it works out the gravel in cubic yards and tons, the length of pipe, the filter fabric to line the trench, how much the trench must fall from end to end, and how much soil you’ll dig out. A 50 ft trench 12 inches wide and 24 inches deep with a 4-inch pipe needs about 2.77 cubic yards (3.55 tons) of gravel and should drop 6 inches over its length.
How a French drain works
Water seeps through the soil into the gravel, which has plenty of open space, then into the perforated pipe and flows downhill to an outlet away from the house. HGTV explains that the most reliable French drains use slotted pipe, filter fabric and gravel; drains built without fabric can clog with sand and soil over time. Slotted pipe lets in less fine soil than pipe with small round holes.
How to use the French drain calculator
- Choose US or metric units.
- Enter the trench length from the wet area to the outlet.
- Enter the width and depth of the trench.
- Enter the soil cover: the depth of soil or turf over the gravel. It starts at 5 inches.
- Choose the pipe size, and enter the gravel price per ton to see the cost.
The calculations
- Gravel = length × width × (depth − soil cover) − the volume of the pipe, converted to cubic yards. Tons use 2,565 lb per cubic yard, the same default as the gravel calculator; check the figure for your stone with your supplier.
- Pipe = the trench length.
- Fabric lines the bottom and both sides of the gravel, plus about 10 inches on each side to fold over the top, as HGTV describes.
- Fall = 6 inches for every 50 ft, the slope HGTV recommends, which is 1%.
Worked example
A 50 ft trench, 12 inches wide and 24 inches deep, with 5 inches of soil over the gravel and a 4-inch pipe:
- Soil dug out: 50 × 1 × 2 = 100 cubic feet
- Gravel: 50 × 1 × (19 ÷ 12) = 79.2 cubic feet, less 4.4 cubic feet for the pipe = 74.8 cubic feet, or 2.77 cubic yards
- Weight: about 3.55 tons
- Pipe: 50 ft
- Fabric: 12 + 2 × 19 + 2 × 10 = 70 inches wide, or about 292 sq ft
- Fall: 6 inches from the top end to the outlet
Building a French drain step by step
- Plan the route. HGTV suggests a slightly downward route at least 1 meter from walls and fences, clear of trees and posts, ending where the water won’t affect neighbors.
- Call 811 to have underground lines marked before you dig.
- Dig the trench with a steady slope; check it with a level and string line as you go.
- Add a layer of gravel in the bottom; HGTV uses about 3 inches.
- Line the trench with fabric, leaving extra on both sides.
- Lay the pipe on the gravel and cover it completely with more gravel.
- Fold the fabric over the top of the gravel, then backfill with soil and replace the turf.
Trench width and depth
Sizes vary with the job. A shallow trench across a soggy lawn can be narrow, while a drain beside a basement foundation goes much deeper. HGTV’s yard drain uses a 6-inch-wide trench no deeper than the nearest foundation, and its foundation tips call for a trench at least 2 feet wide that can reach 6 feet deep for a basement. The calculator works for any size you enter, so try a few to compare the gravel needed.
Common mistakes
- No slope. Water only flows if the pipe falls steadily toward the outlet.
- Skipping the fabric. Without it, soil washes into the gravel and pipe.
- Nowhere for the water to go. Plan the outlet first: a dry well, a swale or a lower part of the yard.
- Using rounded sand-sized fill. Washed gravel leaves space for water; fine material fills it.
Choosing the gravel
Use clean, washed stone with plenty of open space between the pieces so water can move through it quickly. Avoid gravel mixed with fine dust or sand, which packs down and blocks the flow. Ask your supplier for drainage stone, and check its weight per cubic yard; if it differs from 2,565 lb, the tons in the calculator will change in proportion. Buying a little more than the calculator shows covers settling and uneven trench walls.
Metric units
In metric mode, enter the length in meters and the width, depth and soil cover in centimeters. The calculator gives the gravel in cubic meters and metric tons, the pipe in meters, the fabric in square meters and the fall in centimeters. The gravel price is then per metric ton, with no currency sign, so you can use any currency.
How long does a French drain last?
A well-built French drain can work for many years. The parts most likely to fail are the fabric and the pipe if soil gets in, so lining the whole trench and covering the gravel matter more than the type of pipe. Keep the outlet clear of leaves and debris so the water always has somewhere to go.
Price other stone jobs with the gravel calculator, and measure an irregular yard with the square footage calculator.
What next
Use this often? Add French Drain to your Home screen.
Frequently asked questions
How does the French drain calculator work out gravel?
It multiplies the trench length and width by the gravel depth (trench depth minus soil cover), subtracts the pipe, and converts the volume to cubic yards and tons.
How much slope does a French drain need?
HGTV recommends a fall of 6 inches for every 50 feet, which is 1%.
How much gravel do I need for a 50 ft French drain?
For a trench 12 inches wide and 24 inches deep with a 4-inch pipe and 5 inches of soil cover, about 2.77 cubic yards, or 3.55 tons.
Do I need filter fabric for a French drain?
Yes. Fabric keeps soil out of the gravel and pipe, so the drain doesn’t clog over time.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.