The epoxy calculator tells you how much mixed epoxy resin you need for a coating or a pour. Enter the length and width of a rectangle, or the diameter of a round top, and the thickness you want, and it works out the volume in US gallons or liters. Add a waste allowance and pick your mix ratio, and it splits the total into resin and hardener. For example, a 6 × 3 ft tabletop coated 1/8 inch thick needs about 1.4 gallons of mixed epoxy, or about 1.61 gallons with 15% added for waste.
How the epoxy calculator works
Epoxy is measured by volume, so the calculator multiplies the area by the thickness and converts the result to gallons:
- Volume (cubic inches) = area (sq ft) × 144 × thickness (in)
- Gallons = cubic inches ÷ 231, because one US gallon is exactly 231 cubic inches
In metric units it’s even simpler: 1 square meter covered 1 millimeter thick takes exactly 1 liter. For a round top, the area is π × (diameter ÷ 2)².
Jamestown Distributors, which sells TotalBoat epoxy, gives the same coverage for one gallon of mixed epoxy: about 25.6 sq ft at 1/16 inch, 12.8 sq ft at 1/8 inch and 6.4 sq ft at 1/4 inch, before waste.
How to use the epoxy calculator
- Choose US or metric units. US uses feet for the size and inches for the thickness; metric uses meters and millimeters.
- Pick the shape: rectangle or circle.
- Enter the size of the surface to cover or the mold to fill.
- Enter the thickness. You can type a fraction like 1/8 or 1 1/2, or a decimal like 0.125.
- Add a waste allowance for epoxy left in cups, on tools and running off the edges.
- Choose the mix ratio on your kit: 1:1, 2:1 or 3:1 resin to hardener by volume.
Worked examples
Tabletop flood coat: a 6 × 3 ft table is 18 sq ft. At 1/8 inch, that’s 18 × 144 × 0.125 = 324 cubic inches, or 1.4 gallons. With 15% waste, mix about 1.61 gallons: 0.81 gallon each of resin and hardener for a 1:1 kit.
Round top: a 3 ft round table poured 1/4 inch deep has an area of 7.07 sq ft and needs 1.1 gallons. With a 2:1 epoxy, that’s 0.73 gallon of resin and 0.37 gallon of hardener.
Garage floor coat: a 20 × 20 ft floor coated 10 mils (0.010 inch) thick needs about 2.49 gallons of 100%-solids epoxy per coat.
Metric: a 1.8 × 0.9 m tabletop at 3 mm needs 4.86 liters.
How much to add for waste
The calculator works out the exact volume, but you never get every drop onto the project. Jamestown Distributors suggests conservatively allowing 15 to 20% for epoxy lost in the mixing cup, drips, brushes, rollers and spreaders. Flood coats that run over the edges of a tabletop lose more, so tape the underside or set the piece on a tarp to catch drips. For a deep pour into a sealed mold, little runs off, so a smaller allowance is usually enough.
Coating vs. deep pour epoxy
Epoxies are made for different jobs. Tabletop and coating epoxies are designed for thin layers and often have a maximum pour depth per layer on the label. Deep pour or casting resins cure more slowly so they can fill river tables and molds in thicker layers without overheating. Always follow your product’s limit: if your project is deeper than one layer allows, split the total from the calculator over several pours and let each layer cure as directed.
Mix ratios and measuring
The mix ratio printed on the kit is usually by volume, such as 1:1 or 2:1. With a 2:1 epoxy, two-thirds of the mixed total is resin and one-third hardener. Measure carefully in marked cups, mix for the time the maker states, scraping the sides and bottom, and mix only as much as you can pour before the epoxy starts to set. If your kit gives the ratio by weight instead, follow the weights on its data sheet rather than these volumes.
Tips for a better result
- Seal porous wood first with a thin seal coat, so air in the wood doesn’t bubble up into the flood coat.
- Work in the right temperature range on the label; cold epoxy is thick and slow to cure.
- Level the surface before pouring so the epoxy settles evenly.
- Buy a little more than you need from the same batch, so a second mix matches the first.
Converting thickness
Epoxy thickness is described in several ways. Floor coatings are usually given in mils, where one mil is a thousandth of an inch, so 10 mils is 0.010 inch. Tabletop coats are often described as fractions such as 1/16 or 1/8 inch. Casting and river table pours are measured in inches or millimeters. One millimeter is about 0.039 inch, and 1/8 inch is about 3.2 mm. Enter whichever you have, converting mils to inches by dividing by 1,000.
Planning a river table
For a river table, measure the gap between the two slabs rather than the whole table. If the river is irregular, estimate its average width, multiply by the length of the table and the depth of the mold, and enter those sizes. Many makers then add a thin flood coat over the whole top, which you can work out separately as a second calculation with the full table size and a thickness of 1/16 or 1/8 inch.
Measure the area of an odd-shaped room or table with the square footage calculator, and convert between gallons, quarts and liters with the volume converter.
What next
Use this often? Add Epoxy to your Home screen.
Frequently asked questions
How does the epoxy calculator work out how much epoxy I need?
It multiplies the area by the thickness to get the volume, then converts it to gallons (231 cubic inches each) or liters, and adds your waste allowance.
How much does a gallon of epoxy cover?
About 25.6 sq ft at 1/16 inch, 12.8 sq ft at 1/8 inch and 6.4 sq ft at 1/4 inch, before waste.
How much epoxy do I need for a 6 × 3 ft table?
About 1.4 gallons for a 1/8 inch coat, or about 1.61 gallons with 15% extra for waste.
How much extra epoxy should I mix for waste?
Jamestown Distributors suggests allowing 15 to 20% for epoxy left in cups and on tools and drips.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.