A drip faucet calculator shows how much water a leaking tap wastes. Count the drips in a minute, or collect the water for a minute in a cup, and it gives the litres and gallons lost per day, month and year, and the cost if you add your water price.
How to use the drip faucet calculator
- Choose whether you count drips or collect the water.
- Enter the drips per minute or the volume and time.
- Optionally add the drop size and the water price.
- Press Calculate.
What the EPA says
The US Environmental Protection Agency says that a leaky faucet that drips at the rate of one drip per second can waste more than 3,000 gallons per year [1]. It also says that a showerhead leaking at 10 drips per minute wastes more than 500 gallons per year [1]. These two figures fit together if each drip is about 0.36 millilitres, which is the drop size the calculator uses when you leave the size blank. That drop size is our own inference from the two figures.
The average household
The EPA says that the average household's leaks can account for more than 9,300 gallons of water wasted every year [1], and another page gives 180 gallons per week, or 9,400 gallons a year, from household leaks [2]. Nationwide, the pages give figures of nearly 900 billion gallons and nearly 1 trillion gallons a year, and the two pages do not quite agree [1][2]. A single dripping tap is therefore a good part of the typical household loss.
Counting drips
If you count the drips in a minute, the calculator multiplies by the volume of a drip and by the minutes in a day and a year. With 60 drips a minute at the default drop size, the waste is 3,000 gallons a year, or about 11,356 litres. With a smaller drop of 0.1 millilitre, the same rate wastes about 833 gallons. The result is a direct multiplication, and the drop size is the main uncertainty.
Measuring the water
A more accurate way is to put a measuring cup or a small jar under the drip, and note how much water it collects in a known time. Enter the millilitres and the seconds. If you collect 15 millilitres in a minute, the waste is 15 millilitres a minute, which is 21.6 litres a day and about 2,083 gallons a year. A longer collection time gives a better result, because a drip rate can vary.
The cost
Enter your price per 1,000 gallons to see the cost of the lost water. At 5 per 1,000 gallons, 833 gallons a year costs about 4.17. The figure does not include the cost of heating the water if it is a hot tap, or the sewer charge, which is often added to the water bill. Adjust the price to your total rate if you wish.
Gallons and litres
The calculator gives both units. A US gallon is exactly 3.785411784 litres, a figure from the definition of the gallon, so 3,000 gallons are 11,356 litres. In a metric country, use the litre figure. The results are rounded to a few digits, since the inputs are not precise.
Fixing the leak
Most dripping faucets come from a worn washer or seal, which is a cheap part. The EPA runs a campaign called Fix a Leak Week to encourage people to look for leaks [1]. Check the faucets, the toilets and the showerheads, as all can leak. A quick test for a toilet is to put a drop of food colouring in the tank and see if the colour appears in the bowl without flushing.
Why it matters
Water is valuable and the energy used to treat and pump it is wasted along with it. A small leak adds up over a year. The calculator turns the number of drips into a volume that you can picture, such as a bathtub or a swimming pool, and that makes the case for a quick repair.
Putting the loss in perspective
A bathtub holds about 40 gallons, so a tap that wastes 3,000 gallons a year loses the equivalent of 75 full tubs. A leak that fills a cup in a minute, about 237 millilitres, would waste more than 124,000 litres in a year, which shows how a fast drip becomes a steady stream. Use the measuring mode to see where your own leak sits between these extremes.
A simple repair log
Note the date, the rate of the leak and the result of your repair. Check again after a week, as a new washer can still leave a slow drip if the valve seat is rough. If the leak remains, a plumber can replace the cartridge or the valve. Run the calculator once more to confirm that you have fixed the loss.
Common mistakes
- Guessing the drop size. Measure the volume when you can.
- Counting for a few seconds only. Count for a full minute.
- Forgetting hot water costs. Heating adds to the cost.
- Ignoring other leaks. Check toilets and showerheads too.
What next
Use this often? Add Drip Faucet to your Home screen.
Frequently asked questions
What is a drip faucet calculator?
A tool that shows how much water a dripping tap wastes from its drip rate or from a measured volume.
How much water does a dripping faucet waste?
The EPA says that one drip per second can waste more than 3,000 gallons a year.
How big is a drip?
It varies. The EPA's figures imply about 0.36 millilitres, but a measured volume is more reliable.
How much do household leaks waste?
The EPA says the average household wastes more than 9,300 gallons a year through leaks.
How do I measure a drip rate?
Collect the water in a measuring cup for a known time, then enter the millilitres and the seconds.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.