A drain slope calculator shows how much a drain pipe must drop over its length so that waste water and solids flow away. If a drain is too flat, solids settle and clog. If it is much too steep, water can run ahead of the solids. This calculator multiplies the run by the slope to give the fall in inches or millimetres, and shows the same slope as a percent and a ratio.
How to use the drain slope calculator
- Pick US or Metric.
- Choose the slope: 1/4 inch per foot or 1/8 inch per foot.
- Enter the horizontal length of the pipe run.
- Press Calculate. The result is the total drop from the high end to the low end.
The slope rule for drains
The federal construction standard for manufactured homes says horizontal drainage piping must have a uniform grade of not less than 1/4 inch per foot toward the drain outlet [1] Where the structure makes that impractical, a grade of not less than 1/8 inch per foot is allowed if a full-size cleanout is installed at the upper end of the pipe [1] Wikipedia explains the general principle that a sufficient fall must be kept throughout the drain pipes so that liquids and solids flow toward the main drain [2] That page does not give a number. Model plumbing codes set their own minimum slopes by pipe size, and the cut-offs change between editions, so confirm which applies to you.
The formula
Fall = run × slope. A slope of 1/4 inch per foot is 0.25 ÷ 12 = 0.020833, or 2.083 percent. A slope of 1/8 inch per foot is 1.042 percent. As a ratio, 1/4 inch per foot is about 1 in 48 and 1/8 inch per foot is about 1 in 96.
Worked example
A drain runs 40 feet horizontally. At 1/4 inch per foot the fall is 40 × 0.25 = 10 inches. At 1/8 inch per foot it is 40 × 0.125 = 5 inches. In metric, a 12 metre run at 1/4 inch per foot (2.083 percent) falls 250 millimetres.
Fall for common run lengths
| Run | Fall at 1/4 in per ft | Fall at 1/8 in per ft |
|---|---|---|
| 5 ft | 1.25 in | 0.625 in |
| 10 ft | 2.5 in | 1.25 in |
| 20 ft | 5 in | 2.5 in |
| 30 ft | 7.5 in | 3.75 in |
| 40 ft | 10 in | 5 in |
| 50 ft | 12.5 in | 6.25 in |
Why a cleanout comes with the lower slope
A flatter pipe moves solids less well, so a blockage is more likely. The manufactured home rule allows the lower slope only with a full-size cleanout at the upper end of the pipe, so the line can be reached and cleared [1] The calculator reminds you of this when you choose 1/8 inch per foot.
How to set the slope on site
- Measure the horizontal run, not the length along the sloping pipe.
- Mark the high end and the low end, and work out the fall.
- Use a level with a slope marker, or hang the pipe from a string line set at the fall.
- Support the pipe so it cannot sag. A sag holds water and collects solids.
- Check the whole run with a level before you glue or backfill.
Drain slope in a longer run
Long drains are often built in sections. Work out the total fall for the whole run, then check that every section keeps the same slope, with no flat or reverse stretch. If the pipe has to pass under a beam or footing and you are short of height, the fall can add up faster than expected: a 60 foot run at 1/4 inch per foot needs 15 inches of drop from end to end. Plan the low end first so the outlet is below the lowest fixture.
Converting between inch per foot, percent and ratio
To change inches per foot into a percent, divide by 12 and multiply by 100. For example 3/8 inch per foot is 0.375 ÷ 12 = 3.125 percent. To get a ratio, divide 12 by the inches per foot: 12 ÷ 0.25 = 48, so one inch of fall for every 48 inches of run. The calculator shows both for the slope you choose, which helps when a drawing gives the slope in a different form.
Metric drain slopes
In metric work, a fall in millimetres per metre is easy to read. A slope of 1/4 inch per foot is about 20.8 millimetres of fall per metre, and 1/8 inch per foot is about 10.4 millimetres per metre. Choose Metric above to enter the run in metres and to see the fall in millimetres.
Common mistakes
- Treating the minimum slope as the same for every pipe size. Codes often change the figure by diameter, so check the table that applies.
- Making the slope steeper than needed to be safe. Very steep drains can leave solids behind.
- Measuring the fall along the pipe instead of using the horizontal length.
- Forgetting that vertical drops and vents have their own rules.
Limits of this calculator
The tool applies the slope you choose to the run you enter. It does not look up the minimum for your pipe size, and it does not check venting, trap arm length or a fixture's rules. The figures cited here come from the manufactured home standard, which is one specific rule. Your job may fall under a different code. Check with your local plumbing inspector before you build.
What next
Use this often? Add Drain Slope to your Home screen.
Frequently asked questions
How does the drain slope calculator work?
It multiplies the horizontal run by the slope you choose, 1/4 or 1/8 inch per foot, to give the total fall. It also shows the slope as a percent and a ratio.
What is the standard slope for a drain pipe?
A common figure is 1/4 inch per foot. The federal manufactured home standard requires at least that, and allows 1/8 inch per foot only with a full-size cleanout. Your local code may differ.
How much fall do I need for a 40 foot drain?
At 1/4 inch per foot a 40 foot run needs 10 inches of fall. At 1/8 inch per foot it needs 5 inches.
Is 1/4 inch per foot the same as 2 percent?
Almost. 1/4 inch per foot is 0.25 divided by 12, which is 2.083 percent, or about 1 in 48.
Can a drain be too steep?
Yes. If a drain is much too steep, water can run ahead of solids and leave them behind. Follow the minimum and maximum in your local code.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.