A DNA copy number calculator converts between the mass of DNA and the number of molecules. Enter the mass of double-stranded DNA, such as a plasmid or a PCR product, and its length in base pairs, and it gives the number of copies. It also works backwards from a copy number to a mass, and shows the molar mass and the mass of one molecule.
How to use the DNA copy number calculator
- Choose copies from the amount of DNA, or the reverse.
- Enter the amount and the length in base pairs, and choose the mass unit.
- Press Calculate.
The calculation
The number of copies is the mass divided by the molar mass of the DNA, multiplied by the Avogadro constant. The molar mass of the DNA is its length in base pairs times the molar mass of a base pair. The Wikipedia article on the Avogadro constant gives its exact value as 6.02214076 × 10 to the power 23 per mole, and says it converts the average mass of one particle to its molar mass.[2] The article on base pairs says that one base pair corresponds to roughly 618 daltons for DNA, and 643 for RNA.[1] So 1 nanogram of a 1,000 base pair DNA, with a molar mass of 618,000 grams per mole, contains 1 × 10 to the power −9 ÷ 618,000 = 1.618 × 10 to the power −15 moles, which is 9.7446 × 10 to the power 8 copies.
The choice of molar mass
The calculator uses 618 grams per mole for each base pair, the figure on the base pair page.[1] Many laboratory guides use a rounded average of about 650 for double-stranded DNA instead. The pages we read do not give 650, so it is not cited, but you can enter it in the box. With 650, the same nanogram of 1,000 base pairs gives 9.2648 × 10 to the power 8 copies, about 5 percent fewer. Use the value that your protocol or supplier uses, and state it when you report a copy number.
Single-stranded DNA and RNA
The molar mass per base pair applies to double-stranded DNA. For single-stranded DNA the mass per nucleotide is about half as much, which is our own working, and for RNA the page gives 643 daltons per base pair.[1] The calculator does not change the molar mass for you, but you can enter the molar mass per base pair or nucleotide that fits your molecule, and enter the length in the same units, such as nucleotides.
From copies to mass
Choose the second mode to find the mass for a given number of copies. For 10 to the power 9 copies of a 1,000 base pair DNA, the mass is 1.0262 nanograms. This is useful for preparing a standard curve for quantitative PCR, where you dilute a known number of copies. The calculator also shows the mass of a single molecule, 1.0262 × 10 to the power −18 grams in this example.
Worked examples
A plasmid of 4,500 base pairs has a molar mass of 2,781,000 grams per mole. A solution with 10 nanograms of it contains 10 × 10 to the power −9 ÷ 2,781,000 = 3.596 × 10 to the power −15 moles, which is about 2.165 × 10 to the power 9 copies. Reverse the calculation to prepare 10 to the power 6 copies: 10 to the power 6 copies of this plasmid weigh 4.6 picograms. These are our own calculations from the formula above.
Where the numbers go wrong
Small errors in the DNA concentration become errors in the copy number, so measure the stock carefully. The Nucleic acid quantitation page says that absorbance readings can overestimate the DNA concentration when a contaminant such as phenol absorbs at 260 nanometres.[3] Use the dilution that you actually measured, and note that the length must be the length of the molecule that you have, such as the whole plasmid with its insert.
Quantitative PCR standards
For a standard curve, make a stock of known copy number and dilute it in steps of ten. Start with the mass of the stock from your measured concentration, find the copies per microlitre with this calculator, and then plan the dilutions to reach the range of copies that your assay needs, such as 10 to the power 7 down to 10 copies. Use low-binding tubes and carrier nucleic acid for the most dilute standards, because very small amounts stick to plastic. These are common laboratory practices and not from the pages we read.
Copies per volume
If your DNA is at 5 nanograms per microlitre and the molecule is 1,000 base pairs, then each microlitre has 5 times 9.7446 × 10 to the power 8, or 4.87 × 10 to the power 9 copies. Divide by the dilution factor to find the copies in the diluted tubes. Enter the mass per microlitre as the amount to see the copies per microlitre directly.
Checking the result
As a sanity check, 1 nanogram of a 1,000 base pair fragment is around 10 to the power 9 copies, and the number scales with the mass and falls in proportion to the length, so 1 nanogram of a 10,000 base pair plasmid is about 10 to the power 8 copies. If your result is far from these orders of magnitude, check the length, the unit and the exponent. This quick rule is our own.
Common mistakes
- Using the insert length for a plasmid. Use the whole molecule.
- Mixing mass units. Check nanograms against micrograms.
- Forgetting to state the molar mass used. 618 and 650 give different copy numbers.
What next
Use this often? Add DNA Copy Num to your Home screen.
Frequently asked questions
What is a DNA copy number calculator?
A tool that converts the mass of DNA to the number of molecules, using the length in base pairs and the molar mass of a base pair.
How do I calculate copy number from ng?
Copies = mass in grams ÷ (length in bp × molar mass per bp) × 6.022 × 10²³. One nanogram of 1,000 bp at 618 g/mol is about 9.7 × 10⁸ copies.
What molar mass per base pair does it use?
618 g/mol, the figure on the base pair page. You can enter 650 or another value.
What is the Avogadro constant?
6.02214076 × 10²³ per mole, the number of particles in a mole.
Why do copy numbers differ between calculators?
They may use different molar masses per base pair, such as 618 or 650.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.