Saved

Press the star next to a tool's name to save it.

All my tools

Crown Molding Angle Calculator

Use this crown molding angle calculator to get the miter and bevel saw settings for crown molding laid flat, from the wall corner angle and a 38 or 45 degree spring angle.

Restored your last values ·

degrees
degrees

Enter the wall corner angle and choose the spring angle of your crown molding. You get the miter angle and bevel angle for a compound miter saw with the molding laid flat.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the wall corner angle, choose the spring angle, then press Calculate.

See full result

This crown molding angle calculator gives the miter angle and the bevel angle to set on a compound miter saw when you cut crown molding laid flat. You enter the angle of the wall corner and pick the spring angle of your molding, 38 or 45 degrees, and the tool returns both saw settings. It saves you from reading small printed charts and works for corners that are not square, such as 120 or 135 degree bay walls.

Crown molding sits between the wall and the ceiling, so it leans out from the wall. The angle it leans at is called the spring angle, or crown angle, and it is typically sold in 45 and 38 degree formats [1]. Because the piece leans, a cut that looks simple on a flat board turns into a compound cut: you need a miter angle and a bevel angle at the same time [1].

How to use the crown molding angle calculator

  1. Measure the wall corner with an angle finder. A square inside corner is 90 degrees. An outside corner of a square room is also 90 degrees measured on the room side.
  2. Type that angle in the first box.
  3. Choose the spring angle printed on the molding, its packaging or the supplier sheet: 38 degrees, 45 degrees, or Other if yours is different.
  4. Press Calculate and read the miter angle and the bevel angle.
  5. Set both on the saw, lay the molding flat on the saw bed, and cut a scrap piece first.

The formulas

The page for crown molding gives the two formulas for a given spring angle and wall angle [1]. The miter angle is the arctangent of the sine of the spring angle divided by the tangent of half the wall angle. The bevel angle is the arcsine of the cosine of the spring angle times the cosine of half the wall angle [1]. The calculator uses these exactly, with the wall angle you enter and the spring angle you choose.

Compare this with a flat picture frame joint, where each piece is simply cut at half the corner angle, 45 degrees for a 90 degree corner [2]. Crown needs more than that because the molding leans away from the wall, which is why the bevel appears.

Worked example: a square corner with 38 degree crown

Wall angle 90 degrees, spring angle 38 degrees. Half the wall angle is 45 degrees and its tangent is 1. The sine of 38 degrees is 0.6157, so the miter angle is the arctangent of 0.6157, which is 31.62 degrees. The cosine of 38 degrees is 0.7880 and the cosine of 45 degrees is 0.7071, so the bevel is the arcsine of 0.5572, which is 33.86 degrees. These are the familiar 31.6 and 33.9 degree saw settings for 38 degree crown.

With 45 degree crown in the same corner the settings are different: miter 35.26 degrees and bevel 30 degrees.

Saw settings for common wall angles

Wall angle38° spring: miter38° spring: bevel45° spring: miter45° spring: bevel
90°31.62°33.86°35.26°30.00°
120°19.57°23.20°22.21°20.70°
135°14.31°17.55°16.32°15.70°
144°11.31°14.09°12.94°12.62°

Inside and outside corners

The numbers are the same for an inside corner and an outside corner. What changes is which piece goes on which side and which way the saw turns. The page notes that cutting inside and outside corners requires complex cuts at standard angles, usually made with a powered compound miter saw that has stops at those angles [1]. A common routine is to mark each piece on the back with where it goes, cut the left piece for the left side, and cut the right piece with the miter set to the opposite side.

As our own working, remember that the saw direction differs for the two pieces of a corner. Mark the ceiling edge of every piece in pencil so the ceiling edge is the one against the fence.

Tips for better corners

  • Test on scrap. Walls are rarely exactly 90 degrees, and a one degree error opens a visible gap on a long piece.
  • Measure each corner. If two corners differ, enter each wall angle separately and write the settings next to each corner on the wall.
  • Cut a little long and trim to fit. A piece is easier to shorten than to lengthen.
  • Consider coping an inside corner. Coping is an alternative to a mitered inside corner, and corner blocks need only butt cuts [1].
  • Caulk and sand small gaps. Wood moves with the seasons, so a perfect fit on day one can open slightly later.

Finding your spring angle

As our own working, hold a short piece of the molding upside down against a framing square with the back edges touching the square’s two arms. Measure the angle between the back of the molding and the wall arm. That is the spring angle. Most stock crown is one of the two common values. If yours is neither, choose Other and type the measured angle. Values must be more than 0 and less than 90 degrees.

Common mistakes

  • Typing the angle of the cut instead of the wall angle. Enter the corner angle, such as 90, not 45.
  • Using 38 degree settings on 45 degree molding. The saw settings differ, as the table shows.
  • Cutting with the molding in the wrong orientation on the saw. Use the same orientation you used when you planned the cut, and check the result on scrap.
  • Forgetting that the second piece needs the opposite miter direction.

This tool gives the geometry only. Saw scales differ, and some saws read bevel to the left and right differently, so always confirm with a test cut.

What next

Use this often? Add Crown Moldin to your Home screen.

Frequently asked questions

How does a crown molding angle calculator work?

It applies the standard formulas: the miter angle is the arctangent of the sine of the spring angle divided by the tangent of half the wall angle, and the bevel angle is the arcsine of the cosine of the spring angle times the cosine of half the wall angle.

What are the saw settings for 38 degree crown molding in a 90 degree corner?

A miter of 31.62 degrees and a bevel of 33.86 degrees, with the molding laid flat on the saw.

What about 45 degree crown molding?

In a 90 degree corner the settings are a miter of 35.26 degrees and a bevel of 30 degrees.

Are inside and outside corner angles the same?

Yes, the angles are the same for a given wall angle. The pieces simply go on opposite sides and the miter direction is reversed.

What if my wall is not 90 degrees?

Measure the corner with an angle finder and enter that angle. The calculator handles any wall angle between 0 and 180 degrees.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools