This concrete block fill calculator estimates how much grout or concrete you need to fill the cores of a concrete block wall. Enter the size of the wall or the number of blocks, and how many of the cells you'll fill, and the concrete block fill calculator gives the volume in cubic yards, cubic feet and cubic meters, along with the number of bulk grout bags.
How to use the concrete block fill calculator
- Choose how to count the blocks: from the wall size, or by entering the number of blocks.
- Enter the wall length and height (US feet by default) or the block count.
- Enter the share of cells filled: 100% for a fully grouted wall, less if only some cores are filled.
- Press Calculate.
How much grout fills a block?
The Mason Contractors Association of America (MCAA) says that a 3,000-pound bag of grout yields about one cubic yard and fills about 100 standard 8 × 8 × 16-inch blocks. That works out to about 0.01 cubic yards, or 0.27 cubic feet, per fully grouted block, which the calculator uses. If your blocks are a different size or your supplier gives a fill volume per block, enter it in cubic feet to override the default.
Counting blocks from the wall size
According to Wikipedia, US concrete blocks are nominally 16 inches long, and their actual size is 3/8 inch smaller than nominal to allow for 3/8-inch mortar joints. So, with its mortar joint, each nominal 8 × 16-inch block covers 128 square inches of wall face, or 1.125 blocks per square foot. The calculator multiplies the wall area by 1.125 and rounds up.
Worked example
Take a wall 40 feet long and 4 feet high. Its face is 160 square feet, so it holds 160 × 1.125 = 180 blocks. Filling every cell takes 180 × 0.01 = 1.8 cubic yards of grout (48.6 cubic feet or about 1.38 cubic meters), about 1.8 of the 3,000-pound bulk bags. If you only grout half the cells, for example where reinforcing bars run, you need 0.9 cubic yards.
For 100 blocks, fully grouted, the estimate is the MCAA's figure of about 1 cubic yard.
Reading the results
The big number is the grout needed, in cubic yards (or cubic meters in metric). The table shows the number of blocks, the volume in other units and the number of 3,000-pound bulk bags.
Ordering grout
The MCAA explains that contractors can order masonry grout by compressive strength from ready-mix companies, who deliver by the cubic yard, or mix it on site from bulk bags or separate materials. For large walls, ready-mix grout pumped into the cores can place 10 cubic yards or more an hour. For smaller jobs, bagged grout mixed in a mortar mixer is often more practical. Either way, round up and allow for some waste.
Partially grouted walls
Not every wall is fully grouted. Often only the cells with vertical reinforcing bars, plus bond beams, are filled. Count the cells you'll fill as a share of the total, or count the blocks in the filled cells and use the Number of blocks option. Blocks usually have two cores each, so filling one core in every block is about 50%.
Metric walls
Choose metric to enter the wall length and height in meters. The calculator converts the wall area to square feet to count the standard US blocks, then shows the grout in cubic meters. One cubic yard is about 0.76 cubic meters, so the MCAA's figure of about one cubic yard per 100 blocks is about 0.76 cubic meters. Blocks made to metric sizes in other countries have different cores, so for those, enter the fill per block from the maker's data.
Why core volume varies
Wikipedia notes that most blocks have two cores and that the cores are tapered, and some blocks have three or four cores. Different makers use slightly different core shapes, so the volume per block isn't exactly the same everywhere. The 0.27 cubic feet per block used here comes from the MCAA's estimate for standard 8-inch blocks, and it's a reasonable planning figure, but a block maker's published core volume will be more precise.
Openings and bond beams
If the wall has doors or windows, subtract their area before counting the blocks, or count the blocks directly. Bond beam blocks, which carry horizontal reinforcement, are usually fully grouted even in walls where only some vertical cells are filled, so add them to your count at 100%.
Before you pour
Clean mortar droppings out of the cores, check that any reinforcing bars are in place, and make sure cleanouts at the bottom of tall walls are closed. Pour in lifts and consolidate each one so the grout fills the cells completely.
Common mistakes
- Using the actual block size for counting. Use the nominal size, which includes the joint.
- Forgetting partial fill. Enter less than 100% if only some cells are grouted.
- Ignoring block type. 6-inch and 12-inch blocks have different cores.
- Ordering the exact amount. Add extra for waste.
Tips
- Check the block maker's data for core volume.
- Order ready-mix for big walls to save labor.
- Consolidate the grout as you pour to avoid voids.
What next
Use this often? Add Concrete Blo to your Home screen.
Frequently asked questions
How does a concrete block fill calculator work?
It counts the blocks and multiplies by about 0.01 cubic yards of grout per standard 8 × 8 × 16 block.
How much concrete to fill 100 blocks?
About 1 cubic yard for standard 8 × 8 × 16 blocks, according to the MCAA.
How many blocks are in a square foot of wall?
About 1.125 standard blocks, since each nominal 8 × 16 block covers 128 square inches.
How much grout to fill a block wall?
Multiply the number of blocks by 0.01 cubic yards, and by the share of cells you fill.
Can I use the calculator for other block sizes?
Yes, enter the fill volume per block from the block maker's data.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.