Saved

Press the star next to a tool's name to save it.

All my tools

Buckling Calculator

Use this buckling calculator to find the Euler critical load and stress of a slender column from its section, length, end conditions and material, with the slenderness ratio.

Restored your last values ·

Choose US or metric units, the cross-section, the end conditions and the material. Enter the size and the length of the column. You get the Euler critical load and stress, the slenderness ratio, and, with a yield strength, a check of whether the column buckles or yields first.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the size and the length of the column, then press Calculate.

See full result

A buckling calculator finds the load at which a long, slender column buckles. Enter the cross-section, the length, the end conditions and the material, and it gives the Euler critical load and stress and the slenderness ratio. With a yield strength it tells you whether the column buckles before it yields.

How to use the buckling calculator

  1. Choose US or metric units and the cross-section.
  2. Choose the end conditions and the material.
  3. Enter the size and the length.
  4. Press Calculate.

Euler's formula

The critical load of a slender column is P_cr = π² E I ÷ (K L)², where E is Young's modulus of the material, I the minimum second moment of area of the cross-section, L the unsupported length and K the effective length factor [1]. The formula was derived by Leonhard Euler in 1744 [1]. Above this load, a perfectly straight column bows sideways and collapses.

End conditions

The factor K depends on how the ends are held. The page gives K = 1 for a column simply supported at each end [1]. For the other cases, the calculator uses the standard theoretical values of 2 for one end fixed and one free, 0.7 for one fixed and one pinned, and 0.5 for both ends fixed. These three values appear in a figure on the page that we could not read, so they are our own working.

Critical stress

The critical stress is σ = P_cr ÷ A = π² E ÷ (L_e ÷ r)², where L_e = K L is the effective length and r = √(I ÷ A) is the radius of gyration, and L_e ÷ r is the slenderness ratio [1]. The page notes that for slender columns the critical buckling stress is usually lower than the yield stress [1]. The calculator shows the stress, the slenderness ratio and the radius of gyration.

A worked example

A solid steel bar of 50 millimetres diameter and 1.5 metres long, pinned at both ends, has I = 306,800 mm⁴, using E = 200 gigapascals as in the page's chart for steel [1]. The critical load is 269.15 kilonewtons, the critical stress is 137.08 megapascals and the slenderness ratio is 120. With both ends fixed, the load is four times as large, 1,076.6 kilonewtons. These figures are our own calculations.

The role of yield

The page shows a chart of critical stress against slenderness for steel with a yield strength of 240 megapascals [1]. If the critical stress comes out above the yield strength, the column would yield before it buckles, and Euler's formula does not apply. In the calculator, enter the yield strength: for the bar above, 240 megapascals is higher than 137, so buckling governs. The same bar at 0.5 metres would yield first.

Other sections

For a round tube, enter the outer and inner diameters. For a rectangle, enter the width and the depth, and the calculator uses the weaker axis, which has the smaller second moment of area. A tube of 50 millimetres outside and 40 inside has I = 181,130 mm⁴ and uses only 36 percent of the material of the solid bar, so tubes are efficient columns.

Materials

Steel is entered as 200 gigapascals, which the page gives for the steel of its chart [1], and aluminium as 69 gigapascals, which is our own figure. For another material, choose it and enter its Young's modulus. In US mode the modulus is in millions of pounds per square inch, where steel is about 29, and the yield strength in ksi. The calculator converts them using 6.894757 megapascals per ksi.

Assumptions

The page lists the assumptions of the formula: the column is initially straight, the end joints are frictionless, and it fails only by buckling while the stress stays below yield [1]. A real column has an initial bend, loads that are off the axis and residual stresses, all of which lower its capacity. Johnson's parabolic formula is used for columns of low slenderness [1], which this calculator does not include.

Safety

Structural designers use design codes that include factors for these effects, and a large factor of safety against the Euler load. The calculator gives only the ideal value. It should not be used to decide whether a real column is safe. Use it for learning, for a first estimate of how the load depends on the length and the diameter, and for checking the answers to an exercise.

Using the calculator

Choose the units, the section, the ends and the material, then enter the size and the length. Compare different end conditions to see their effect. A longer column falls as the square of the length: doubling it cuts the load to a quarter. Increasing the diameter raises the load with the fourth power. The working line shows the second moment of area that was used.

Effect of the length

The critical load falls with the square of the effective length. Take the 50 millimetre steel bar with pinned ends: at 1 metre the Euler load is 605.6 kilonewtons, at 1.5 metres 269.1 kilonewtons, and at 3 metres only 67.3 kilonewtons. Halving the length therefore multiplies the load by four. This is our own calculation from the formula, and it shows why long, thin members are braced at intermediate points.

Common mistakes

  • Using the radius as the diameter. Enter the diameter.
  • Ignoring the end conditions. K changes the load by a factor of 16.
  • Using Euler for short columns. They yield before they buckle.
  • Treating the result as a safe load. Apply a design factor.

What next

Use this often? Add Buckling to your Home screen.

Frequently asked questions

What is a buckling calculator?

A tool that finds the load at which a long column buckles.

What is Euler's critical load?

P_cr = π² E I ÷ (K L)².

What is the effective length factor for a pinned column?

K = 1.

What is the slenderness ratio?

The effective length divided by the radius of gyration, K L ÷ r.

When does Euler's formula not apply?

When the critical stress is above the yield strength, for short, stocky columns.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools