Saved

Press the star next to a tool's name to save it.

All my tools

Board on Board Fence Calculator

Use this board on board fence calculator to count the pickets, sections, posts and rails you need from the fence length, post spacing, picket width and overlap.

Restored your last values ·

Enter the fence length, the space between posts, the picket width and the number of rails in each section. Leave the overlap blank to use the recommended overlap of 24% of the picket width. The calculator gives the pickets, sections, posts and rails.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the fence length, post spacing, picket width and rails, then press Calculate pickets.

See full result

A board on board fence calculator works out how many pickets a board-on-board fence needs, and how many sections, posts and rails. Enter the fence length, the space between posts, the picket width and how much the pickets overlap, and the calculator does the counting. If you leave the overlap blank, it uses the recommended overlap of 24 percent of the picket width. It runs in your browser and nothing you enter is sent anywhere.

What a board on board fence is

A board-on-board fence has pickets fixed to the rails in two layers, so that each picket overlaps its neighbors. There are no gaps between the boards, which gives privacy even when the wood shrinks. Because of the overlap, a section needs more pickets than a fence with the boards edge to edge, and the calculation has to take the overlap into account.

How to use the board on board fence calculator

  1. Choose US or Metric units.
  2. Enter the fence length and the post spacing.
  3. Enter the picket width and, if you want, the overlap.
  4. Enter the rails in each section and press Calculate pickets.

The picket formula

The number of pickets is the fence length minus the picket width, divided by the picket width minus the overlap, plus one. The three values must be in the same units, and if the result has a decimal part, it is rounded up to the next whole number. The reason is simple: the first picket covers one picket width, and each further picket adds only the part that is not covered, which is the width minus the overlap. This is our own working, based on how the boards overlap. The calculator changes your units for you, so you can enter feet for the length and inches for the pickets.

How much overlap

The calculator's default is our own rule of thumb: multiply the picket width by 0.24 to get the overlap. The idea is that the overlap should be at least twice the shrinkage you expect, and we assume a worst case of 12 percent of the width. Wood shrinks across the grain by roughly 2 to 10 percent as it dries [1], so 12 percent leaves a margin. A 3.5-inch picket gets an overlap of 0.84 inch, a 5.5-inch picket 1.32 inches and an 11.5-inch picket 2.76 inches. The calculator uses 24 percent when you leave the overlap blank.

Worked examples

An 8-foot section, which is 96 inches, takes 24 pickets of 5.5 inches with an overlap of 1.5 inches, and 38 pickets of 3.5 inches with an overlap of 1 inch. You can check this: for the first, 96 minus 5.5 is 90.5, divided by 4 is 22.6, and plus one is 23.6, which rounds up to 24. Now take a 40-foot fence with posts every 8 feet and 5.5-inch pickets with the recommended overlap of 1.32 inches. It needs 115 pickets, five sections, six posts, and with three rails in each section, 15 rails.

Posts, sections and rails

Posts, rails and sections are worked out as in a conventional fence, which is built from posts connected by boards and rails [2]. The calculator therefore divides the fence length by the post spacing and rounds up to get the sections, adds one to get the posts for a straight fence, and multiplies the rails in each section by the number of sections. It also shows the pickets in one section, which is useful if you build the fence in panels.

What to add

The count is the minimum. Add boards for waste, for splits and for mistakes, and for gates, which need their own pickets. Corners and ends may need more posts. The calculator does not include the post length, the concrete or the hardware, which depend on your fence height and your soil.

Reading the result

The calculator shows the pickets for the whole fence, the number of sections, the posts, the rails and the pickets in one section. The overlap it used is shown too, so that you can see whether it is the value you typed or the recommended one. Use the picket count to buy boards, and the section figures to plan the work. If you build panels on the ground and lift them into place, the pickets in one section tell you how many boards each panel takes, and the section count tells you how many panels to make.

Planning the fence

Before you buy, walk the fence line and measure it in straight runs. A fence that turns corners is best entered one run at a time, because each run has its own end posts and its own part-section at the end. Add up the pickets for the runs and compare the total with the figure for the whole length. The two can differ by a few boards, because each run is rounded up on its own. Decide where the gates go and take that length out of the fence length, since a gate is built differently from a section.

Choosing the picket width

Wider pickets cover more ground, so fewer boards are needed, but they shrink more across their width, and a wider picket needs a wider overlap. Narrow pickets need more boards and more nails or screws, but each board moves less. The calculator lets you try both: enter 3.5 inches and then 5.5 inches and compare the totals. The examples for an 8-foot section above show the difference clearly, with 38 narrow pickets against 24 wide ones.

Spacing the rails

The number of rails in each section is your choice, and it depends on the height of the fence. Taller fences usually have more rails so that the boards stay straight. The calculator multiplies the rails you enter by the number of sections, so you can compare two plans quickly.

Common mistakes

  • Mixing units. The calculator handles the units, so choose US or Metric first.
  • Using the nominal board width. Measure the real width of your picket.
  • Setting the overlap too small. Wood shrinks as it dries, and a gap may open.
  • Forgetting extra boards. Add some for waste and gates.

What next

Use this often? Add Board on Boa to your Home screen.

Frequently asked questions

What is a board on board fence calculator?

A tool that counts the pickets, sections, posts and rails for a fence whose pickets overlap in two layers.

How do you calculate the pickets for a board on board fence?

(Fence length minus picket width) divided by (picket width minus overlap), plus one, rounded up.

How much should the pickets overlap?

The calculator's default is 24 percent of the picket width, our own rule of thumb that allows for the wood to shrink across the grain. You can type your own overlap.

How many pickets are in an 8-foot section?

24 for 5.5-inch pickets with 1.5 inches of overlap, and 38 for 3.5-inch pickets with 1 inch.

Does it include gates and waste?

No. Add spare boards and extra pickets for gates.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools