The fence post depth calculator works out how deep to set a fence post and how big to dig the hole. Enter the post’s height above the ground and choose its size. Using the common rule of thumb, it buries one-third to one-half of the above-ground height, makes the hole three times as wide as the post, adds gravel at the bottom and checks your local frost depth. It also gives the total post length to buy and the bags of concrete to fill the hole. For a 6 ft fence with 4×4 posts, set each post at least 24 inches deep in a 12-inch hole.
How deep should a fence post be?
HGTV explains the general rule: the hole should be one-third to one-half of the post’s above-ground height. For a 6 ft post that’s 2 to 3 ft, and HGTV notes that 3 ft is ideal, though 2 ft may be enough depending on the fence’s weight, the soil and the climate. Trex Fencing says a 6 ft privacy fence usually needs at least 24 inches, its own installation guide recommends at least 30 inches, and holes can go deeper than 36 inches where the frost line is deep.
The calculator shows that one-third to one-half range and uses the one-third figure as the minimum, unless your frost depth is deeper, in which case it sets the post to the frost depth.
How to use the fence post depth calculator
- Choose US or metric units. US uses feet for height and inches for depths; metric uses centimeters.
- Enter the height above ground, which is usually the fence height.
- Choose the post size: 4×4, 6×6 or 4-inch round.
- Enter your frost depth if you know it. Your local building department can tell you.
- Set the gravel depth for the bottom of the hole (4 inches if blank) and the number of posts.
Hole diameter
HGTV’s rule is to make the hole three times the post’s width. A 4×4 or 4-inch round post needs a 12-inch hole, and a 6×6 needs an 18-inch hole. A wider hole gives the concrete more grip on the soil, which helps the post resist wind pushing on the fence.
Worked example: a 6 ft privacy fence
For 4×4 posts standing 6 ft (72 inches) above ground:
- Post depth: one-third to one-half of 72 inches is 24 to 36 inches, so at least 24 inches
- Hole depth with 4 inches of gravel: 28 inches
- Hole diameter: 3 × 4 = 12 inches
- Post length to buy: 72 + 24 = 96 inches, or 8 ft
- Concrete: about 1.23 cubic feet per hole, which is 4 bags of 50 lb or 3 bags of 80 lb
If the frost depth where you live is 36 inches, the post goes 36 inches deep instead, the hole is 40 inches with gravel, and the post needs to be 9 ft long. Ten such posts need about 52 bags of 50 lb concrete.
How the concrete is worked out
The concrete fills the ring between the post and the sides of the hole, from the top of the gravel to about 3 inches below ground, where HGTV suggests stopping so soil or a sloped cap can finish the hole. The calculator takes the area of the hole, subtracts the post (a 4×4 is actually 3½ inches square and a 6×6 is 5½ inches), and multiplies by that depth. Bags are counted using approximate yields for QUIKRETE concrete: about 0.375 cubic feet for a 50 lb bag and 0.6 cubic feet for an 80 lb bag.
Why the frost line matters
In cold climates, water in the soil freezes and expands each winter. If a post sits above the frost line, the freezing soil can lift it a little every year, a problem called frost heave, leaving the fence uneven. Setting the bottom of the post below the frost line keeps it in soil that doesn’t freeze. Frost depths vary from almost nothing in the far South to several feet in the northern states, so ask your local building department.
Setting the post
- Call 811 before you dig, so underground lines can be marked.
- Dig the hole to the full depth and width. A rented auger saves a lot of work on long fences.
- Add the gravel and tamp it down.
- Set and brace the post so it’s plumb on two sides.
- Fill with concrete to about 3 inches below ground, following the directions on the bag.
Gate posts and corner posts
Gate posts carry the swinging weight of the gate, and corner and end posts take the pull of the fence in two directions. These posts work harder than line posts, so many builders set them deeper and in wider holes, or use a larger post such as a 6×6. If you’re hanging a heavy gate, enter a 6×6 post in the calculator to see the bigger hole and extra concrete it needs.
Soil and wind
Loose, sandy or wet soil holds a post less firmly than firm clay, and a solid privacy fence catches much more wind than an open picket or wire fence. HGTV suggests burying posts a little deeper and adding more concrete in soft ground or windy areas. If either applies to you, aim for the one-half end of the depth range rather than the one-third minimum.
Work out the number of posts, rails and pickets for the whole fence with the fence calculator, or the concrete for slabs and footings with the concrete calculator.
What next
Use this often? Add Fence Post D to your Home screen.
Frequently asked questions
How does the fence post depth calculator decide the depth?
It uses the rule of thumb of burying one-third to one-half of the post’s height above ground, with one-third as the minimum, and goes deeper if your frost depth is greater.
How deep should a 6 ft fence post be?
At least 24 inches, and ideally up to 36 inches. Trex Fencing’s installation guide recommends at least 30 inches for a 6 ft fence.
How wide should a fence post hole be?
About three times the width of the post: 12 inches for a 4×4 and 18 inches for a 6×6.
How many bags of concrete per fence post?
For a 4×4 post set 24 inches deep in a 12-inch hole, about 4 bags of 50 lb or 3 bags of 80 lb concrete.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.