A BMEP calculator finds the brake mean effective pressure of an engine from its displacement and its torque, or from its power and speed. The result is a measure of how much work the engine does per unit of displacement, which lets you compare engines of different sizes. It works for four-stroke and two-stroke engines.
How to use the BMEP calculator
- Choose US or metric units and the cycle.
- Enter the displacement.
- Enter the torque, or the power and the speed.
- Press Calculate.
What BMEP is
Mean effective pressure is a measure of an engine's capacity to do work, independent of the engine displacement [1]. The brake mean effective pressure is calculated from the torque measured on a dynamometer [1]. It can be thought of as the average pressure that, acting on the pistons during the power strokes, would give the same output at the crankshaft.
The formulas
The page gives the power as P = i n V_d p_me, where i is the number of cycles per revolution, 0.5 for a four-stroke engine and 1 for a two-stroke, n the speed in revolutions per second and V_d the displacement [1]. With the torque, P = 2π n M, so p_me = 2π M ÷ (V_d i) [1]. The calculator uses these two forms for the torque and the power modes.
The page's example
The page gives an example for a four-stroke engine with a torque of 159 newton metres and a displacement of 2,000 cubic centimetres, which has a pressure of about 1 megapascal [1]. The calculator gives 0.99903 megapascals, or 9.99 bar. For the same engine, at 60 revolutions per second and 1 megapascal, the page gives a power of 60 kilowatts [1].
From the power
The other example on the page is an engine with a rated power of 72 kilowatts at 5,400 revolutions per minute, which is 90 revolutions per second, and a BMEP of 0.80 megapascals [1]. In the power mode, enter 72 kilowatts, 5,400 rpm and 2,000 cubic centimetres, and the calculator gives 0.8 megapascals. The page notes that BMEP at full power is lower than at the torque peak, which happens at a lower speed.
US units
In US mode, the displacement is in cubic inches, the torque in pound-feet, the power in horsepower and the result in psi. An engine of 350 cubic inches with a torque of 200 pound-feet has a BMEP of 86.17 psi. The calculator converts to SI using 1.3558 newton metres per pound-foot, 16.387 cubic centimetres per cubic inch, 745.7 watts per horsepower and 6,894.757 pascals per psi, which are our own conversion factors.
Four-stroke and two-stroke
A four-stroke engine has one power stroke every two revolutions, so i = 0.5, and a two-stroke engine has one per revolution, so i = 1 [1]. For the same torque and displacement, the two-stroke engine therefore has half the BMEP. The calculator has an option for each. The 159 newton metre example gives 0.49951 megapascals as a two-stroke.
Typical values
The page gives maximum BMEP figures for engines, from a table by Spicher: 1.2 megapascals for a motorbike engine, 1.3 for a naturally aspirated passenger car, 1.6 for a naturally aspirated Formula 1 car, 2.0 for a turbocharged diesel car, 2.2 for a turbocharged petrol car, and 2.4 for a turbocharged lorry diesel [1]. Compare your result with these. A higher BMEP shows a more highly stressed engine.
Why use it
Because BMEP does not depend on the displacement or the speed, it allows a fair comparison of engines of different sizes and speeds, and shows how well the cylinders are used. Turbocharging raises the BMEP by packing more air into each cylinder. The page notes that BMEP is calculated, and that mean effective pressure itself cannot be measured [1].
Limits
BMEP gives the average effect on the output shaft, so it includes the losses by friction and pumping. The indicated figure, which is calculated from the pressure in the cylinder, is higher. The calculator uses the torque or the power that you give, and it cannot tell you the cylinder pressure. Measurements should be taken at the crankshaft.
Using the calculator
Choose the units and the cycle, enter the displacement, and either the torque or the power and the speed. Read the BMEP in psi or MPa, and in bar and kilopascals. Compare it with the table above. The working line shows the displacement in cubic centimetres and the factor i that was used, so you can check it.
Power and BMEP
For a four-stroke engine of 2,000 cubic centimetres at 6,000 revolutions per minute, which is 100 revolutions per second, a power of 100 kilowatts corresponds to a BMEP of 100,000 ÷ (0.5 × 100 × 0.002) = 1.0 megapascal. Raise the power to 150 kilowatts at the same speed and the BMEP rises in proportion, to 1.5 megapascals. This is our own calculation, and you can repeat it in the power mode.
Common mistakes
- Using the wrong stroke setting. A two-stroke doubles the factor.
- Using power at the wheels. Use power at the crankshaft.
- Mixing torque and power modes. Fill in the right boxes.
- Comparing a naturally aspirated with a turbo engine directly. Boost raises BMEP.
What next
Use this often? Add BMEP to your Home screen.
Frequently asked questions
What is a BMEP calculator?
A tool that finds the brake mean effective pressure of an engine.
What is the BMEP formula?
p_me = 2π M ÷ (V_d i), with i = 0.5 for a four-stroke engine.
What is a typical BMEP for a petrol car?
About 1.3 MPa for a naturally aspirated engine and 2.2 MPa for a turbocharged one.
Why is the two-stroke value different?
A two-stroke has a power stroke each revolution, so i = 1.
Can I find BMEP from power?
Yes: p_me = P ÷ (i n V_d), with n in revolutions per second.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.