Saved

Press the star next to a tool's name to save it.

All my tools

Birdsmouth Cut Calculator

Use this birdsmouth cut calculator to work out the heel cut height, notch depth and height above plate for a rafter, and check the cut against the one-third rule.

Restored your last values ·

Enter the measured depth of the rafter, the length of the seat cut (often the width of the wall plate it sits on) and the roof pitch as inches of rise per 12 inches of run.

Everything is worked out in your browser. Nothing you type is sent anywhere.

Heel (plumb) cut height

–

Enter the rafter depth, seat cut and pitch, then press Calculate.

See full result

This birdsmouth cut calculator works out the size of the notch where a rafter sits on a wall plate. Enter the rafter's depth, the length of the seat cut and the roof pitch, and the birdsmouth cut calculator gives the heel (plumb) cut height, how deep the notch goes into the rafter, the height above the plate, and whether the notch stays within the common one-third rule.

How to use the birdsmouth cut calculator

  1. Choose US or metric units. US (inches) is the default; the pitch is always rise per 12.
  2. Enter the rafter depth, measured across the board.
  3. Enter the seat cut length, the part of the notch that rests on the wall plate.
  4. Enter the roof pitch, such as 6 for a 6-in-12 roof, then press Calculate.

What is a birdsmouth cut?

The Wikipedia article on the birdsmouth joint describes it as a notch cut into a rafter so it can sit on the top plate of a wall. It has two faces: the seat cut, which rests flat on the top plate, and the heel cut, also called the plumb cut, which runs vertically and sits against the outside of the wall. Together they form a triangle-shaped notch, like an open bird's beak.

The one-third rule

Wikipedia notes that, as a general rule, no more than one third of the depth of the rafter should be removed, to keep the rafter strong. It adds that the allowed depth varies between local building codes, and that the notch shouldn't extend unsupported on the inside of the wall, since the rafter could split along the grain there. The calculator measures the notch depth square to the rafter's edge and compares it with one third of the depth.

How the calculator works

The roof angle is the angle whose tangent is the rise divided by 12. With a horizontal seat cut of length S:

  • Heel cut height = S × rise ÷ 12, measured vertically
  • Notch depth, square to the rafter = S × sin(roof angle)
  • Height above plate = rafter depth ÷ cos(roof angle) − heel cut height, measured vertically from the plate to the top of the rafter

It also works out the longest seat cut that stays within one third: (rafter depth ÷ 3) ÷ sin(roof angle).

Worked example

Take a rafter 5.5 inches deep on a 6-in-12 roof, with a 3.5-inch seat cut. The roof angle is about 26.6°. The heel cut is 3.5 × 6 ÷ 12 = 1.75 inches high, and the notch is 3.5 × sin 26.6° = 1.57 inches deep, about 28% of the rafter's depth, within the one-third rule. The height above the plate is 5.5 ÷ cos 26.6° − 1.75 = 4.4 inches. The longest seat cut within one third would be about 4.1 inches.

On a steeper 8-in-12 roof with a 7.25-inch-deep rafter and a 5.5-inch seat, the notch would be about 3.05 inches deep, 42% of the depth, which is more than one third. A shorter seat cut, or a different detail, would be needed.

Reading the results

The big number is the heel cut height. The line below says how deep the notch is as a share of the rafter depth and whether that's within one third. The table shows the notch depth, the height above the plate, the roof angle and the longest seat cut that stays within one third.

Laying out the cut

Mark the plumb line with a framing square or speed square set to your pitch, then measure up it by the heel cut height. From there, mark the seat line square to the plumb line, level when the rafter is in place, for the seat cut length. Cut along both lines, stopping exactly where they meet so you don't overcut and weaken the rafter. Make one rafter first, test it in place, and use it as a pattern for the rest.

Choosing the seat cut length

The seat cut is usually set by the wall it sits on, often the width of the top plate, so that the rafter bears fully on the wall. On steep roofs, though, a full-width seat can cut deep into the rafter, as the 8-in-12 example shows. The calculator's longest seat cut within one third helps you see how much bearing you can have before the notch gets too deep. If it's less than the plate width, check with your local code or building inspector for an approved detail.

Metric rafters

Choose metric to enter the rafter depth and seat cut in millimeters. The pitch is still entered as rise per 12, since that's how roof pitch is usually stated, and the calculator gives the cuts in millimeters.

Common mistakes

  • Using the nominal size. Measure the actual depth of the rafter.
  • Making the seat too long. A long seat on a steep roof cuts deep into the rafter.
  • Overcutting the corner. Stop each saw cut at the line.
  • Skipping the code. Local rules may limit notching.

Tips

  • Cut a pattern rafter and test it before cutting the rest.
  • Keep the height above plate the same on every rafter so the roof stays flat.
  • Check your building code for notching limits.

What next

Use this often? Add Birdsmouth C to your Home screen.

Frequently asked questions

How does a birdsmouth cut calculator work?

It uses the roof angle to work out the heel cut height (seat × rise ÷ 12), the notch depth and the height above the plate.

How deep can a birdsmouth cut be?

As a general rule, no more than one third of the rafter's depth, though local codes vary.

What is the seat cut on a rafter?

The horizontal face of the birdsmouth that rests on the wall's top plate.

What is a plumb cut?

The vertical face of the birdsmouth, also called the heel cut, that sits against the wall.

How do I find the heel cut height?

Multiply the seat cut length by the rise and divide by 12. A 3.5-inch seat on a 6/12 roof gives 1.75 inches.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools