An angle of repose calculator finds the steepest angle at which a loose material stays in a pile. Give it the height and radius of a heap, a friction coefficient or an angle. It returns the angle, the matching friction coefficient and, if you add a radius, the volume of the cone and the weight of the pile.
How to use the angle of repose calculator
- Choose what you know: height and radius, the friction coefficient or the angle.
- Choose US or metric units.
- Fill in the boxes. Add a radius and a density to see the volume and weight.
- Press Calculate.
What the angle of repose is
The angle of repose is the steepest angle at which a heap of loose material can lie without sliding. Tip sand from a bucket, and it settles into a cone with a fixed slope. Wikipedia states that this angle is equal to the arctangent of the coefficient of static friction between the grains [1]. It is the same idea that engineers use for stockpiles, silos and embankments.
Angle from friction
The relation is θ = arctan(μs). A friction coefficient of 0.6 gives arctan 0.6, which is 30.964 degrees. The reverse is μs = tan θ, so an angle of 34 degrees gives a coefficient of 0.6745. The tool shows both whichever one you enter, and the slope as a percentage grade, which is the tangent times 100. The article gives the relation for loose, cohesionless material [1].
Angle from a heap
If you can measure a pile, the angle follows from the right triangle that its cross section makes. The tangent of the angle is the height divided by the radius, which is the same as twice the height divided by the width. This is our own working from the geometry.
Height from the angle
With the angle and the radius, the height is the radius times the tangent of the angle. This is a rearrangement and it is our own working. A pile of 2 metres radius at 30.964 degrees is 1.2 metres high. Use this mode to predict how tall a pile will be on a base of a given size, for example when you plan where to tip gravel or grain.
Volume and weight
A cone has a volume of π r² h ÷ 3, as Wikipedia states for a circular cone [2]. The weight is the volume times the bulk density, which is our own working, and you enter the density. For a height of 1.2 metres, a radius of 2 metres and 1,600 kilograms per cubic metre, the volume is 5.0265 cubic metres and the weight is 8,042.5 kilograms. In US units the tool also gives cubic yards.
The material table
The tool compares your angle with a table of typical angles that Wikipedia reproduces from the Pocket Ref of 1995 [1]. Dry sand is listed at 34 degrees, soil at 30 to 45 degrees, gravel with sand at 25 to 30 and wheat at 27. The page says that all the values are approximate. We list every material within two degrees of your angle, a margin of our own that allows for that.
Why the angle varies
The angle depends on the grain size, the shape of the grains, the moisture and how the pile was formed. Wet sand is listed at 45 degrees but sand that is water filled at 15 to 30 degrees [1]. Rounder grains give a lower angle. For these reasons, the table is a guide, and a pile that you measure yourself is a better basis for a calculation.
Units
In US mode the height and radius are in feet, the volume in cubic feet and cubic yards, the density in pounds per cubic foot and the weight in pounds. In metric mode they are in metres, cubic metres, kilograms per cubic metre and kilograms. The angle, the friction coefficient and the slope do not depend on the units. Use the same unit for the height and the radius.
Limits
The tool treats the pile as a smooth cone on a flat base. Real piles have a flat top, uneven sides and a base that is not circular. The cone formula is only an estimate for them. The calculator does not model slope stability, cohesion, vibration or the weight of the soil. Do not use it for the design of walls, embankments or silos.
Using the calculator
Choose what you know and fill in the boxes. Press the button and read the angle first, then the materials near it. If the angle does not match the material that you expect, check the moisture and the measurements. Add a radius and a density to turn the cone into a volume and a weight, which is useful to order sand, gravel or grain.
Common mistakes
- Using the diameter instead of the radius. The radius is half the width of the base.
- Mixing feet and metres. Use one unit for the height and the radius.
- Using a table angle for wet, compacted soil. The angle depends on moisture.
- Treating the result as a design value. It is an estimate for a loose pile.
What next
Use this often? Add Angle of Rep to your Home screen.
Frequently asked questions
What is an angle of repose calculator?
A tool that finds the angle of a pile of loose material from its height and radius or from a friction coefficient.
What is the angle of repose formula?
θ = arctan(μs), where μs is the coefficient of static friction. From a heap it is arctan(height ÷ radius).
What is the angle of repose of dry sand?
Wikipedia lists dry sand at about 34 degrees, and says that all the table values are approximate.
Can an angle of repose calculator give the weight of a pile?
Yes. Add a radius and a bulk density. The tool treats the pile as a cone and multiplies its volume by the density.
Why does the angle of repose change?
It depends on the grain size and shape and on the moisture, so a measured pile is better than a table.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.