Saved

Press the star next to a tool's name to save it.

All my tools

Wind Turbine Calculator

Use this wind turbine calculator to find the power in the wind and the power a turbine extracts from the rotor diameter, wind speed and Cp, with the Betz limit and yearly energy.

Restored your last values ·

Choose US or metric units. Enter the rotor diameter and the wind speed. Change the power coefficient or the air density if you know them, and add a capacity factor for the annual energy.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the rotor diameter and the wind speed, then press Calculate.

See full result

A wind turbine calculator estimates the power that a turbine takes from the wind, from the rotor size, the wind speed and the power coefficient. It shows the power in the wind, the Betz limit and the energy per year for a given capacity factor, in US or metric units.

How to use the wind turbine calculator

  1. Choose US or metric units.
  2. Enter the rotor diameter and the wind speed.
  3. Optionally change the power coefficient, the air density and add a capacity factor.
  4. Press Calculate.

The power equation

The power in the wind is P = ½ ρ A v³, where ρ is the air density, A is the swept area of the rotor and v is the wind speed [1]. Because of the cube, the available power increases eightfold when the wind speed doubles [1]. A turbine takes only part of it, given by the power coefficient Cp, which is the ratio of the power it extracts to the power in the wind [2].

The swept area

The rotor sweeps a circle, so the area is π r², where r is the radius, or π d² ÷ 4 for the diameter, a geometric result of our own. A rotor with a radius of 40 metres, a diameter of 80, sweeps 5,027 square metres. The calculator converts feet and miles per hour to metres and metres per second where needed.

Air density

The calculator uses an air density of 1.225 kilograms per cubic metre, the usual value at sea level and 15 degrees Celsius. That figure is not on the pages we read, which give no value for the density, so it is our own entry. Air density falls with altitude and with warmer weather, so enter your own value for a site that is high or hot. The power is directly proportional to the density.

The Betz limit

The Betz limit says that no turbine can capture more than 16/27 of the power in the wind, about 59.3 percent [2]. The page on wind turbines gives the maximum as P = (16/27) × ½ ρ v³ A [3]. The calculator refuses a power coefficient above this limit and shows the Betz power for your inputs, so you can see how close a design can come.

Typical power coefficients

The page says that large modern turbines peak at a power coefficient of 0.45 to 0.50, and that commercial turbines deliver 75 to 80 percent of the Betz limit at their rated speed [2][3]. Above the rated wind speed the blades pitch to lower the coefficient, which can fall to about 0.06 at 25 metres per second [2]. The default of 0.45 in the calculator is at the lower end of the peak range.

A worked example

A turbine with a rotor of 80 metres in a wind of 10 metres per second has 3.08 megawatts in the wind through the rotor, at 1.225 kilograms per cubic metre. With a coefficient of 0.45 it extracts 1.39 megawatts, and the Betz limit is 1.82 megawatts. If it runs at an average of 40 percent of that output over a year, the energy is about 4,855 megawatt-hours. These are our own calculations from the formulas above.

Capacity factor

The capacity factor is the actual yearly output divided by the theoretical maximum, in other words, the output if the turbine ran at full power all the time. The page on wind power gives a range of about 35 to 44 percent, from a summary that we have not checked word for word [1]. The calculator takes the extracted power as the rated output, multiplies by 8,760 hours and by your capacity factor. A real turbine is rated at a particular wind speed, so this is only an estimate.

Using the calculator

Use it to see how the rotor size and the wind speed affect the power: doubling the diameter gives four times the area, and doubling the wind speed gives eight times the power. The cubic law is why wind speed is the most important feature of a site. Compare the result with the nameplate rating of a real turbine and with measured wind data for your location.

Choosing the wind speed

Because power depends on the cube of the speed, an average wind speed understates the power available. If the wind blows at 5 metres per second half the time and at 15 the other half, the average is 10, but the average of the cubes is 1,750, against 1,000 for the cube of the average. For serious estimates, use the distribution of wind speeds at hub height, which site measurements or a wind atlas provide.

Sizing for a home

A small turbine with a rotor diameter of 3 metres in a wind of 6 metres per second extracts about 0.28 kilowatts at a coefficient of 0.3. That is the output for the moment, and over a year the average will be much lower because the wind varies. Enter your own values to see how a small rotor compares with the needs of a house.

Common mistakes

  • Using the radius as the diameter. The calculator asks for the diameter.
  • Using an average wind speed for the cube. The average of the cubes is larger than the cube of the average.
  • Ignoring air density at altitude. Enter the local density.
  • Expecting more than the Betz limit. No turbine can capture more than 59.3 percent.

What next

Use this often? Add Wind Turbine to your Home screen.

Frequently asked questions

What is a wind turbine calculator?

A tool that estimates the power in the wind and the power a turbine extracts, from the rotor size and wind speed.

What is the wind power formula?

P = ½ ρ A v³, multiplied by the power coefficient Cp for the power the turbine takes.

What is the Betz limit?

16/27, about 59.3 percent: the most of the wind's power that any turbine can capture.

What is a typical power coefficient?

Large modern turbines peak at about 0.45 to 0.50.

What happens when the wind speed doubles?

The power in the wind increases eightfold.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools