Saved

Press the star next to a tool's name to save it.

All my tools

Water Demand Calculator

Use this water demand calculator to estimate the average, maximum-day and peak water demand of a town from its population and the water each person uses, in gallons or litres.

Restored your last values ·

people
%
×
×

Enter the number of people served and the water use per person per day. Leave the waste allowance and the two peaking factors blank to use 10 percent, 1.4 and 2.3. You get the average, maximum-day and peak demand.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the population and the water use per person, then press Calculate.

See full result

A water demand calculator estimates how much water a town or a development needs, from its population and the water each person uses. It gives the average daily demand, the maximum daily demand and the peak demand, which are the three figures that water supply designers use to size pipes, pumps and storage.

How to use the water demand calculator

  1. Pick US or metric units.
  2. Enter the population and the water use per person per day.
  3. Add the waste allowance and the two factors, or leave them blank for the defaults.
  4. Press Calculate.

The three demand figures

Water engineers describe demand at three levels. The average daily demand, or ADD, is the typical amount used in a day over a year. The maximum daily demand, MDD, is the busiest day of the year, usually in a hot, dry spell. The peak demand, PHD, is the busiest hour or period of that day. The City of Winnipeg's water and waste department sets out all three for its design work, and gives the multipliers that link them [1]. The calculator follows that structure.

The formulas

The average daily demand is the water use per person times the population, plus an allowance for waste. The maximum daily demand is the average multiplied by the maximum-day factor, and the peak demand is the average multiplied by the peak-hour factor. In symbols: ADD equals use times population times one plus the waste percentage divided by 100; MDD equals 1.4 times ADD; PHD equals 2.3 times ADD. The factors of 1.4 and 2.3 are the ones given by Winnipeg [1].

Reading the 10 percent allowance

Winnipeg writes the average daily demand as 225 litres per capita per day plus 10 percent [1]. The page does not say whether the 10 percent is a multiplier on the whole figure. We read it as times 1.1, so that the 10 percent is added on top of the base use. This reading is our own.

A worked example in US units

Take 100,000 people, 60 gallons each per day and a 10 percent allowance. The average daily demand is 100,000 times 60 times 1.1, which is 6,600,000 gallons a day. The maximum day is 1.4 times this, or 9,240,000 gallons, and the peak is 2.3 times the average, or 15,180,000 gallons a day. Dividing the peak by the 86,400 seconds in a day gives 175.69 gallons a second.

A worked example in metric units

The Winnipeg design value of 225 litres per person a day is the metric default. For 100,000 people the average daily demand is 100,000 times 225 times 1.1, which is 24,750,000 litres a day. The maximum day is 34,650,000 litres and the peak is 56,925,000 litres, which is 658.85 litres a second. Converted at 3.785411784 litres to the US gallon, the average is 6.54 million gallons, and the US default of 60 gallons per person is close to 227 litres.

The per second figure

The Winnipeg page names the peak figure the peak hour demand and sets it at 2.3 times the average daily demand [1]. To give a rate, we divide the peak daily volume by the 86,400 seconds in a day and show it per second beside the daily volume, and say so in the result. If you need a peak flow for an hour, divide the peak daily volume by 24 instead, which is our own simple alternative.

Choosing the water use per person

Winnipeg uses 225 litres per capita per day for residential demand [1], and the US default here is 60 gallons, which is our own planning figure. Neither is a universal value. Water use depends on climate, price, metering, the share of garden watering and the age of the housing. If you have meter data for your own area, use it instead of a default. The tool accepts any positive number, so you can test low and high cases and see how the three demands move in step.

Other uses on the Winnipeg page

The Winnipeg page also lists design rates for non-residential land: 16,800 litres per hectare per day for commercial areas, 22,500 for light industrial and 33,600 for wet industrial [1]. It gives 3.05 people for each single-family dwelling and 2.30 for each multi-family unit [1]. The calculator does not use these values directly, but you can multiply them out to get a population or a daily figure and then enter that.

Limits of the calculator

The factors of 1.4 and 2.3 are Winnipeg's design values and not a world standard. Other cities use other factors, and real demand depends on weather and growth. The calculator does not include fire flow, losses in the pipes, seasonal tourists or future growth. A real design must use local standards, and it should be checked by a licensed engineer. Use this tool for quick estimates, for teaching and for sense checks of larger models.

What the page does not say

The Winnipeg page does not explain how the 10 percent was set, and it does not say whether the figures are still current. It gives no breakdown of use by activity, such as washing or gardening. We have not used any other figure than these, and where we added a step, such as the per second rate, we have said that it is our own.

Common mistakes

  • Applying the waste allowance twice. Enter it once, as a percentage of the base use.
  • Mixing gallons and litres. Check the unit shown next to the box for the water use.
  • Using the peak figure as a yearly total. It is a rate for a short peak, not an annual volume.
  • Copying the factors for another city. Use the local values for design work.

What next

Use this often? Add Water Demand to your Home screen.

Frequently asked questions

What is a water demand calculator?

A tool that estimates the average daily, maximum daily and peak water demand of a population from the water each person uses.

What is the formula for average daily demand?

Water use per person times the population times one plus the waste percentage divided by 100.

What are the maximum-day and peak-hour factors?

The defaults are 1.4 for the maximum day and 2.3 for the peak, which are the City of Winnipeg's design values.

How is the demand per second worked out?

The peak daily volume divided by 86,400 seconds in a day. This is our own way of showing a rate.

Can I use it for engineering design?

Only as a first estimate. A real design needs local standards and a licensed engineer.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters