A two photon absorption calculator estimates how many excitations per molecule a focused laser produces through two-photon absorption. Enter the cross-section, the laser power, the wavelength, the focus spot size and the exposure time, and it gives the photon flux and the number of excitations.
How to use the two photon absorption calculator
- Enter the cross-section in GM and the laser power in watts.
- Enter the wavelength in nm and the FWHM spot size in µm.
- Enter the exposure time in seconds.
- Press Calculate.
What two-photon absorption is
In two-photon absorption, a molecule takes in two photons together to reach an excited state that would need one photon of twice the energy. Maria Goeppert-Mayer predicted the effect in 1931 in her doctoral dissertation, and it was confirmed experimentally about thirty years later [1]. Because it needs two photons at once, it is only efficient where the light is very intense, such as in the focus of a pulsed laser.
The energy condition
Wikipedia says that the energy gap of the transition is equal to or smaller than the sum of the energies of the two photons [1], and a photon of wavelength λ has the energy hc ÷ λ [3]. For two identical photons from one laser, this tool takes the transition energy as E(n) − E(0) = 2hc ÷ λ, where λ is the wavelength of the laser. The two photons may in general have different energies, but the calculator assumes identical ones. The calculator shows this transition energy in joules and in electronvolts.
The beam radius
The tool converts the focus spot size to a beam radius with w = FWHM ÷ √(2 ln 2), where FWHM is the full width at half maximum of the spot. This follows from the Gaussian relation FWHM = 2√(2 ln 2) σ [4], with the beam radius w equal to 2σ, which is our own step. With a 20 µm FWHM, the radius is 16.986 µm, or 1.6986 × 10⁻³ cm. The calculator works in centimetres from here on, because the cross-section is defined with centimetres in its units.
The peak intensity
For a Gaussian beam, the peak intensity is I = 2P ÷ (π w²), where P is the laser power and w the waist radius [2]. With 10 W and the radius above, and w in centimetres, the intensity comes out in watts per square centimetre: about 2.2064 × 10⁶ W/cm². The calculator shows this value, so you can see how tightly focused the beam is.
The photon flux
The flux of photons through the centre of the beam is φ = I λ ÷ (h c), which is the intensity divided by the energy of one photon, h c ÷ λ [3]. Combining the steps gives φ = 4 P ln 2 × λ ÷ (π FWHM² h c), which is our own algebra. We use the exact SI values of h and c: 6.62607015 × 10⁻³⁴ J s and 299,792,458 m/s [3].
Excitations per molecule
The number of excitations is N = ½ δ φ² τ, where δ is the cross-section in cm⁴ s per photon and τ is the exposure time. The probability of absorption depends on the square of the light intensity [1], which is why the flux is squared. One GM, a Goeppert-Mayer unit, is 10⁻⁵⁰ cm⁴ s per photon [1]. The calculator converts your cross-section in GM before it squares the flux. Because the flux is squared, N depends strongly on the power and on the spot size.
The worked example
Take δ = 210 GM, P = 10 W, λ = 840 nm, FWHM = 20 µm and τ = 1 s. The photon flux is 9.3299 × 10²⁴ photons per cm² per second, and N is about 91.4. The energy of the transition at 840 nm is 4.7296 × 10⁻¹⁹ J, which is 2.952 eV.
How the result scales
Our own reading of the formulas is that N grows with the square of the power, because the flux is proportional to P and N to the flux squared. N also falls with the fourth power of the spot size, because the flux goes as one over FWHM squared. Doubling the power therefore quadruples N, and halving the spot size multiplies it by 16.
The equivalent one-photon wavelength
Because the transition energy is 2hc ÷ λ, a single photon that does the same job has half the wavelength of the laser. For an 840 nm laser, that is 420 nm. This is our own working from the energy condition. It helps you to see which one-photon absorption band the two-photon process matches.
Limits of the model
The model is a Gaussian beam, with the flux taken at the centre of the focus, and it gives no allowance for pulsed lasers, duty cycle or the shape of the pulses in time. Treat the result as a first estimate of the order of magnitude, and check the figures against measurements for your own dye and your own laser setup.
Unit conversions in the calculator
The calculator converts your entries before it applies the formulas. The spot size in micrometres is multiplied by 10⁻⁴ to give centimetres, the wavelength in nanometres is converted to metres for the flux, and the cross-section in GM is multiplied by 10⁻⁵⁰ to give cm⁴ s per photon. These steps are our own bookkeeping, and they are why you can type the figures in the units shown beside the boxes.
A second check
For a different check, enter 100 GM, 0.01 W, 800 nm, a 1 µm spot and 0.001 s. The photon flux comes out at 3.5543 × 10²⁴ photons per cm² per second, and N is about 0.0063164. These figures are our own, from running the same formulas. A small value of N like this means the molecule is excited only rarely in that exposure.
Common mistakes
- Using the wavelength of a one-photon band. Enter the laser wavelength, which is twice as long.
- Entering the cross-section in cm⁴ s. The box takes GM.
- Entering the full width as a radius. Enter the FWHM; the tool finds the radius.
- Expecting a linear change with power. N goes with the square of the power.
What next
Use this often? Add Two Photon A to your Home screen.
Frequently asked questions
What is a two photon absorption calculator?
A tool that estimates the photon flux and the excitations per molecule for a focused laser.
What is the formula for the number of excitations?
N = ½ δ φ² τ, with δ the cross-section, φ the photon flux and τ the time.
What is a GM?
A Goeppert-Mayer unit, 10⁻⁵⁰ cm⁴ s per photon.
Why does doubling the laser power quadruple N?
The photon flux doubles, and N depends on the square of the flux.
What does the calculator assume about the beam?
A Gaussian beam, with the flux at the centre of the focus and two identical photons.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.