Saved

Press the star next to a tool's name to save it.

All my tools

Thrust Weight Calculator

Use this thrust weight calculator to find the thrust-to-weight ratio of an aircraft, rocket or drone from the total thrust and the weight, in US or metric units, with a note on take-off.

Restored your last values ·

Choose US or metric units. In US units, enter the thrust in pounds-force and the weight in pounds. In metric units, enter the thrust in kilonewtons and the mass in kilograms. Add up the thrust of all engines first.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the total thrust and the weight, then press Calculate.

See full result

A thrust weight calculator divides the thrust that engines can produce by the weight of the vehicle. The result, the thrust-to-weight ratio, tells you how strongly an aircraft, rocket or drone can accelerate and whether it could lift off straight up. Enter the total thrust and the weight or mass.

How to use the thrust weight calculator

  1. Choose US or metric units.
  2. Enter the total thrust of all the engines.
  3. Enter the weight (US) or the mass (metric).
  4. Press Calculate.

The formula

The thrust-to-weight ratio is the available thrust divided by the weight: TWR = thrust ÷ weight [1]. Both values must be in the same kind of unit, so that the ratio has no unit. Pounds-force against pounds, or newtons against newtons, give the right answer directly.

Weight is not mass

If thrust is in newtons, the weight must be found from a mass first, as W = m g, and weight should not be confused with mass [1]. In metric mode the tool multiplies your mass by the standard gravity 9.80665 m/s², the value defined by ISO 80000 [2], to get the weight in newtons. In US mode a pound of mass weighs a pound-force, so no conversion is needed.

A metric example

As an example, two engines of 40 kilonewtons each give a total thrust of 80 kN on an aircraft of 10,000 kg. The tool gives 0.8158, since 80,000 N divided by 98,066.5 N is 0.8158, which rounds to 0.82. The ratio is below 1, so this aircraft cannot take off straight up and would need its wings.

A US example

A fighter with 19,000 pounds-force of thrust and a weight of 20,000 pounds has a ratio of 0.95. Type those two numbers in US mode and the tool gives 0.95. A jet with 29,560 lbf and 26,500 lb gives 1.115.

Why 1 matters

For a vehicle to take off from the ground using only thrust, the thrust-to-weight ratio of the whole vehicle must be greater than one [1]. Aircraft are different, since wings supply lift, so a ratio below 1 is normal for airliners. The tool states which case you are in. When the ratio is above 1, it also gives the net upward acceleration, (TWR − 1) × 9.80665 m/s², which is our own working and ignores drag and the change in mass.

Which thrust and weight

The answer changes with the types of thrust and weight that you choose. For aircraft, the quoted ratio is often the maximum static thrust at sea level divided by the maximum take-off weight, but empty weight or combat weight is also used, and some figures include afterburners [1]. Figures on different bases cannot be compared directly. State your basis when you quote a ratio. The calculator takes whatever you enter, and does not choose for you.

Engines and multiple units

Add up the thrust of all engines before you enter it. Two engines of 40 kN give 80 kN, and four of 10,000 lbf give 40,000 lbf. If you want to compare two designs, run the calculator for each and compare the ratios. A higher ratio means a stronger climb and acceleration, at the cost of a bigger or hungrier engine.

Other uses

The same ratio is used for drones and rockets. For a multirotor drone, designers often want a ratio well above 1 so that it can hover and manoeuvre, which is general background rather than a sourced figure. For a rocket, the ratio changes as the fuel burns and the weight falls, so quote the value at lift-off. For a car or a boat, the ratio is less meaningful.

What the tool does not do

The calculator does not model drag, lift, the change of engine thrust with speed and altitude, or the fuel burned. It gives a single ratio at one set of conditions. In steady cruise the ratio equals the drag divided by the lift, TWR = 1 ÷ (lift ÷ drag) [1], which this tool does not compute. Use it as a quick screening number, not as a prediction of climb rate or take-off distance.

Using the results

Enter the thrust and the weight, press Calculate, and read the ratio and the comment. Try the same engines with a lighter vehicle to see how the ratio rises, or half the fuel load for a fighter. Round sensibly: a ratio of 0.82 and one of 0.8158 mean the same for a quick check. Keep the units consistent, and remember that a kilonewton is a thousand newtons.

Reading the result

Large airliners have ratios of roughly 0.2 to 0.3 at maximum take-off weight, while fighters are near 1 or above, as a published table lists: about 0.87 for an F-35A with full fuel and 1.15 for a Eurofighter Typhoon in interceptor configuration [1]. For your own numbers, the useful question is how far the ratio is from 1, since that sets the climb of a rocket or a hovering drone.

Common mistakes

  • Entering a mass in newtons mode. Metric mode takes kilograms.
  • Using the thrust of one engine. Add all the engines.
  • Mixing lb and kg. Pick one system with the toggle.
  • Comparing different bases. Use the same thrust and weight type.

What next

Use this often? Add Thrust Weigh to your Home screen.

Frequently asked questions

What is a thrust weight calculator?

A tool that divides the thrust of the engines by the weight of the vehicle to give the thrust-to-weight ratio.

What is the thrust-to-weight ratio formula?

TWR = thrust ÷ weight, with both in the same kind of unit.

What ratio is needed to lift off vertically?

More than one, since the thrust must exceed the weight.

Why does the basis of thrust and weight matter?

Afterburner or normal thrust and empty or gross weight give different ratios for the same aircraft.

Does the calculator include drag or lift?

No. It gives a single ratio at one set of conditions.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools