A rabbit cage size calculator gives the smallest cage that suits your rabbit from three measurements: one hop, the length lying down and the height standing up. You can also enter the size of an enclosure that you have, and the calculator checks it against a fixed minimum from the Rabbit Welfare Association and Fund.
How to use the rabbit cage size calculator
- Choose US or metric units.
- Measure one hop, the length lying down and the height standing on the hind legs.
- Optionally enter the length, width and height of your enclosure.
- Press Calculate.
The measured rabbit method
This tool sizes the cage from your rabbit. The length is three times the length of one hop, the width is the length of the rabbit lying down, and the height is the height of the rabbit standing on its hind legs. This is the tool's own planning method, and its hop count is in line with the advice of a rabbit retailer that a hutch should allow at least three or four hops [2]. Floor area is the length multiplied by the width. The calculator follows these rules and shows the result in feet and centimetres.
A worked example
For a small rabbit, take a hop of 1.5 feet (45 cm) and a lying length of 2 feet (60 cm). Three hops are 4.5 feet, the width is 2 feet and the floor area is 9 square feet. With a standing height of 1.5 feet, the minimum cage is 4.5 × 2 × 1.5 feet.
Larger rabbits
For a large rabbit, take a lying length of 3 feet (90 cm) and a hop of 2 feet (60 cm). Three hops are then 6 feet. The floor area is 6 × 3 = 18 square feet. A larger rabbit takes bigger hops, so the cage must grow in length faster than in width, and the formula reflects this.
The fixed minimum
The Rabbit Welfare Association and Fund gives a different kind of rule. It asks for a single enclosed area of at least 3 metres by 2 metres by 1 metre high for two average rabbits, and says that a lone rabbit needs the same [1]. Sleeping quarters should be at least 1.8 metres by 0.6 metres by 0.6 metres [1]. The tool shows these figures in feet as well. They are far larger than the measured minimum for one small rabbit.
What does not count
The same page says that upper floors, tunnels and platforms do not count towards the enclosure area [1]. Only the ground space is counted. When you enter the length, width and height of your enclosure, enter the single area of the floor and its height, not the total of several levels. The calculator treats the longer side as the length, so the order of your length and width does not matter.
The fit check
If you enter all three sizes of your enclosure, the calculator compares them with both minimums. It says whether each one is met and, if not, by how much each side falls short. A cage can pass the measured minimum and still fall far short of the fixed one, as a 6 × 3 × 2 foot cage does. Both lines are shown, so you can see how much more room is needed.
Another retailer's figures
The Rabbit House, a retailer that quotes the Code of Practice and the Rabbit Welfare Association, gives other numbers: a living space of at least 12 square feet, a width of 2 feet for small and medium rabbits and 3 feet for large ones, a height of 2 feet, and room for three or four hops [2]. It also describes a run of 32 square feet, for example 8 × 4 feet [2]. The sources disagree, so the calculator shows the measured minimum and the fixed one and leaves you to judge.
Exercise space
The Rabbit House gives a minimum exercise run of 32 square feet, such as 8 × 4 feet [2]. The calculator repeats this as a note. A cage that is only large enough to turn around in needs a safe, larger area for daily exercise, and the time out of the cage matters as much as its size.
What is not stated
No page that we opened gives a size by the weight of the rabbit in kilograms, and none defines an average rabbit. The measured minimum is for one rabbit, and the fixed minimum from the Rabbit Welfare Association and Fund is for two average rabbits, with a lone rabbit needing the same [1]. Nothing is given for more than two rabbits. For this reason, the tool does not offer a weight table.
Using the result
Measure the hop by watching the rabbit move on a flat floor, from the nose at the start to the nose at the end. Measure its length from nose to tail when it is lying stretched out, and its height when it stands. Use the largest of several measurements. Then treat the result as a floor, not a target: bigger is better, and a rabbit should always be able to hop, stretch and stand up.
Our own working
The multiplication by three, the use of the lying length and the standing height, and the floor area are our own planning method. Converting between feet and centimetres, and checking your enclosure against both minimums, are our own steps. When your enclosure is shown as met for the measured rabbit but not met for the Rabbit Welfare Association and Fund, believe the larger figure if the welfare of the rabbit is your aim, since the measured method gives only the least room that lets it hop and stretch.
Common mistakes
- Measuring a rabbit that is curled up. Measure it stretched out.
- Counting platforms as floor. Only the ground area counts.
- Using one rabbit's size for two. Pairs need more room.
- Treating the minimum as ideal. It is the smallest acceptable size.
What next
Use this often? Add Rabbit Cage to your Home screen.
Frequently asked questions
What is a rabbit cage size calculator?
A tool that finds the smallest cage for a rabbit from three measurements of the rabbit, and checks an enclosure against a fixed minimum.
How is the cage length worked out?
It is three times the length of one hop. The width is the length lying down and the height is the standing height.
What does the Rabbit Welfare Association and Fund recommend?
A single enclosed area of at least 3 metres by 2 metres by 1 metre high for two average rabbits, and a lone rabbit needs the same.
Do platforms and tunnels count towards the size?
No. The Rabbit Welfare Association and Fund says that upper floors, tunnels and platforms do not count.
Is this minimum enough for a pair of rabbits?
Not the measured one, which is for a single rabbit. The fixed 3 m by 2 m by 1 m minimum is for two average rabbits.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.