A pump horsepower calculator finds the power that a pump needs from the flow rate, the head and the efficiency. It gives the hydraulic power, which goes into the liquid, and the shaft power, also called the brake power, which the motor must supply, in watts, kilowatts and horsepower.
How to use the pump horsepower calculator
- Pick US or metric units.
- Enter the flow rate, the head and the efficiency.
- Add the specific gravity for a liquid other than water.
- Press Calculate.
What the tool calculates
The pump power delivered to the shaft depends on the flow rate, the differential head, the fluid density and the pump efficiency [1]. The hydraulic power is the same product without the efficiency. In SI units the flow is in cubic metres per second, the head is in metres and the efficiency is a fraction from 0 to 1.
The formulas
The hydraulic power is Ph = Q H ρ g, and the shaft power is Ps = Q H ρ g ÷ η, which is the form P = Δp Q ÷ η with Δp = ρ g H [1]. The efficiency is Ph ÷ Ps, the ratio of the power given to the fluid to the power supplied to the pump [1]. The calculator uses g = 9.81 metres per second squared, close to standard gravity of 9.80665 [3], and for water a density of 1,000 kilograms per cubic metre. The efficiency is entered as a percentage here, which is easier to use.
The worked example
Take a flow of 10 cubic metres per hour, a head of 3 metres, a density of 1,000 and an efficiency of 0.79. The hydraulic power is 81.75 watts and the shaft power is 103.48 watts. These hold only once the flow is turned into 10 ÷ 3,600 cubic metres per second. The calculator does this, and gives the same figures, 0.1388 horsepower.
Horsepower
The power first comes out in watts. The Wikipedia article on horsepower defines one imperial horsepower as 33,000 foot-pounds-force per minute, or about 745.7 watts [2]. We use that to give the result in horsepower. The example of 103.48 watts is about 0.139 hp. In US mode the answer is first in horsepower, and in metric mode it is first in kilowatts.
US units
In US mode the flow is in US gallons per minute and the head is in feet. We convert them with exact definitions: a gallon is 3.785411784 litres and a foot is 0.3048 metres, our own working. For 100 gpm at 50 ft and an efficiency of 70 percent, the hydraulic power is 943.23 watts, or 1.265 hp, and the shaft power is 1,347.5 watts, or 1.807 hp.
Compared with the 3960 rule
Pump data sheets often use hp = gpm × head in feet × specific gravity ÷ 3960 ÷ efficiency. The Wikipedia article does not give that rule. It gives hydraulic horsepower as the pressure in psi times the flow in gpm divided by 1,714 [2]. The values differ by a fraction of a percent, because of the rounded constants, and ours uses g = 9.81.
Head
The head is the differential head, the energy added to each unit weight of liquid, which in practice is the lift plus the pressure difference and the friction loss in the pipes, in metres or feet of the liquid. This is the usual meaning of head in pump work, and it is our own explanation. A pressure gauge reading must be converted into head for the liquid before you enter it.
Specific gravity
For a liquid other than water, the density changes the power. Enter the specific gravity, the density relative to water, and the calculator multiplies the density of 1,000 kilograms per cubic metre by it, our own working. A liquid with a specific gravity of 0.8 needs 80 percent of the power of water for the same flow and head: for the metric example the hydraulic power drops from 81.75 to 65.4 watts.
Efficiency
The shaft power is always larger than the hydraulic power, because no pump is perfect. A smaller efficiency gives a larger shaft power, and cavitation can lower the efficiency by eroding the pump [1]. Take the efficiency from the pump curve at your duty point, not from the best efficiency figure. A motor must supply the shaft power, and a motor rating is usually chosen above it.
What is not included
This calculator does not estimate the specific speed from the pump speed, since the formula changes with the unit system. It also does not size motors, drives or pipes, and gives no cost. For a power bill, multiply the shaft power by the hours of use and divide by the motor and drive efficiency, and check the figures with the supplier.
Scaling and a quick check
The power is in direct proportion to the flow, the head and the specific gravity, and inversely proportional to the efficiency, as the formulas show. Doubling the flow at the same head doubles the hydraulic power, and a pump that runs at 50 percent efficiency needs twice the shaft power of one at 100 percent. For a quick check, the metric example of 10 cubic metres per hour at 3 metres needs 81.75 watts of hydraulic power, and 103.48 watts at the shaft with an efficiency of 79 percent. In US mode, 100 gpm at 50 ft with an efficiency of 70 percent gives 1.807 hp at the shaft. This is our own run of the formulas with the unit definitions above. Always compare the answer with the pump curve and a motor rating from the supplier.
Common mistakes
- Entering the efficiency as 0.79. Enter 79 for 79 percent.
- Using the lift only as the head. Include pressure and friction losses.
- Forgetting the specific gravity of a heavy liquid. It scales the power.
- Choosing the motor at exactly the shaft power. Leave a margin.
What next
Use this often? Add Pump Horsepo to your Home screen.
Frequently asked questions
What is a pump horsepower calculator?
A tool that finds the power a pump needs from the flow, head and efficiency.
What is the pump horsepower formula?
Shaft power = flow × head × density × g ÷ efficiency; the hydraulic power is the same without the efficiency.
What is the difference between hydraulic and shaft power?
Hydraulic power goes into the liquid; shaft power is what the motor supplies, larger by the efficiency.
How many watts is one horsepower?
One imperial horsepower is about 745.7 watts.
Does the liquid matter?
Yes. A heavier liquid needs more power for the same flow and head; enter its specific gravity.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.