Saved

Press the star next to a tool's name to save it.

All my tools

Prop Pitch Calculator

Use this prop pitch calculator to find a boat propeller's pitch, speed or slip from the engine rpm, the gear ratio and the other two values, in US or metric units.

Restored your last values ·

rpm
%

Choose whether to find the propeller pitch, the boat speed or the slip. Enter the engine rpm, the gear ratio and the other two values. Use US units (mph and inches) or metric units (km/h and millimetres).

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find and fill in the other values, then press Calculate.

See full result

A prop pitch calculator finds the pitch of a boat propeller from the boat speed, the engine rpm, the gear ratio and the slip. It also works the other way, to give the speed from a given pitch, and it finds the slip from the speed, so it doubles as a prop slip calculator.

How to use the prop pitch calculator

  1. Choose what to find: pitch, speed or slip.
  2. Pick US or metric units.
  3. Enter the rpm, the gear ratio and the other two values.
  4. Press Calculate.

What pitch is

A propeller's pitch is the distance it would move the boat forward in one revolution, so a 21-inch pitch propeller would move a boat 21 inches with each turn [1]. A propeller in water does not move that far, because the water gives way, and the shortfall is the slip, usually expressed as a percentage of the pitch [2]. The pitch can be worked out from the boat speed, the gear ratio, the engine speed and the slip.

The pitch formula

The formula used here is pitch = speed × gear ratio × C ÷ (engine rpm × (1 − slip)), with the result in inches. The constant C depends on the speed unit: 1,056 for miles per hour, 656 for kilometres per hour and 1,215.2 for knots. They come from turning the speed into inches per minute, for example 63,360 inches in a mile divided by 60 minutes gives 1,056, and this is our own working. The slip is a ratio between 0 and 1. In the calculator it is entered as a percentage, and the result is shown in inches and millimetres.

Speed from pitch

The speed follows by rearranging: speed = pitch × rpm × (1 − slip) ÷ (gear ratio × C). For a 16 inch pitch at 5,500 rpm, with a 2 to 1 gear ratio and 10 percent slip, the arithmetic gives 37.5 mph. The calculator gives that figure, and also shows the speed in knots and kilometres per hour.

Pitch from speed

For 50 mph at 5,500 rpm with a 2 to 1 gear ratio and 20 percent slip, the formula gives a 24 inch pitch: 50 × 2 × 1,056 ÷ 5,500 gives 19.2, and 19.2 ÷ 0.8 gives 24. The calculator gives 24 in, which is 609.6 millimetres. This is the default mode, and the example values appear in the boxes as grey hints.

Prop slip

Slip is the shortfall between the theoretical and the actual travel, as a percentage of the pitch [1]. In speed terms, slip = (theoretical speed − actual speed) ÷ theoretical speed × 100, with theoretical speed = pitch × engine rpm ÷ (gear ratio × C) and C = 1,056 for mph and inches. For example, take a 24 inch pitch at 6,000 rpm with a 2 to 1 gear ratio: the theoretical speed is 68.18 mph, and 60 mph actual gives 12 percent slip. The calculator's slip mode gives 12 percent.

A second slip example

A second example is a 25 inch pitch with 65 mph at the same rpm and gear ratio. The theoretical speed is 71.02 mph and the slip 8.48 percent. The calculator gives 8.4 percent for this case, using the same formula. People also search for a prop slip calculator, and this one covers it with its slip mode.

What slip is normal

As a rough guide, slip is about 30 percent for displacement boats, 20 to 25 percent for planing hulls and 10 to 12 percent for faster performance boats [1][2]. The calculator tells you whether your slip is inside 10 to 20 percent, which is our own range for a typical boat. A negative slip means that the boat is going faster than the pitch, rpm and gear ratio allow, which usually means a wrong input or a different propeller.

Metric units

The constant for kilometres per hour is 656 for a pitch in inches. In the metric mode of the calculator the pitch is in millimetres, and our own constant is 1,000,000 ÷ 60 = 16,667, which comes from converting millimetres per minute into kilometres per hour. An example is 80 km/h at 5,500 rpm, a 2 to 1 ratio and 20 percent slip, which gives about 606 mm, or 23.9 inches.

The gear ratio

The gear ratio is the number of engine turns for each turn of the propeller. A direct drive has a ratio of 1. Leave the box blank for 1. A 2 to 1 gear halves the propeller speed, so the theoretical speed is halved too. Check the lower unit's ratio in the manual, since an outboard may have a ratio like 2.15 to 1.

Using the results

If the engine cannot reach the minimum rpm rated by its maker at full throttle, the pitch should be decreased, and each extra inch of pitch lowers the rpm by roughly 200 [2]. A lower pitch also gives more acceleration [1]. If the engine passes its maximum rating, the pitch is probably too low, which is our own guidance, so ask a propeller shop. Treat the number as a starting point.

Checking the examples

The default values are 50 mph, 5,500 rpm, a 2 to 1 gear ratio and 20 percent slip, which give a pitch of 24 inches. The calculator also shows that the theoretical speed for that pitch is 62.5 mph, and that 50 mph is 80.467 km/h or 43.449 knots, our own conversions with 1 mph = 1.609344 km/h and 1 knot = 1.852 km/h exactly [3]. Switching to the speed mode with a 16 inch pitch, 5,500 rpm, a 2 to 1 ratio and 10 percent slip gives 37.5 mph, with a theoretical speed of 41.667 mph. Switching to the slip mode with a 24 inch pitch, 6,000 rpm, a 2 to 1 ratio and 60 mph gives 12 percent. The three modes use one formula, so you can move between them to test a change in rpm or gearing and see what it does to the pitch.

Common mistakes

  • Entering the engine rpm instead of the propeller rpm. Use the gear ratio for the difference.
  • Typing slip as a decimal. Enter 20 for 20 percent.
  • Mixing mph with a pitch in millimetres. Pick one unit system.
  • Expecting the pitch to give the real speed. Slip makes the real speed lower.

What next

Use this often? Add Prop Pitch to your Home screen.

Frequently asked questions

What is a prop pitch calculator?

A tool that finds a boat propeller's pitch from the speed, rpm, gear ratio and slip.

What is the prop pitch formula?

Pitch = speed × gear ratio × C ÷ (rpm × (1 − slip)), with C = 1,056 for mph and inches.

How is prop slip calculated?

Slip = (theoretical speed − actual speed) ÷ theoretical speed, as a percentage.

What is a normal prop slip?

It depends on the boat: roughly 10 to 12 percent for fast performance boats, 20 to 25 percent for planing hulls and about 30 percent for displacement boats.

What is the gear ratio?

The number of engine turns for each turn of the propeller.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters