A pool volume calculator tells you how much water your swimming pool holds, which you need for dosing chlorine and other chemicals, sizing a pump or heater, and estimating the cost of filling it. Choose the pool's shape, enter its size and depth, and this calculator gives the volume in US gallons, with liters, cubic feet and the water surface area too. US units are the default, and you can switch to meters and liters.
The pool volume formulas
A pool's volume is the area of the water's surface multiplied by its average depth:
- Rectangle: length × width × average depth
- Round: π × (diameter ÷ 2)² × average depth
- Oval: π × (length ÷ 2) × (width ÷ 2) × average depth
If the floor slopes from a shallow end to a deep end, the average depth is (shallow + deep) ÷ 2. The result is in cubic feet or cubic meters, and the calculator turns it into gallons or liters.
From cubic feet to gallons
A US gallon is defined as exactly 231 cubic inches, and a cubic foot is 12 × 12 × 12 = 1,728 cubic inches. That makes one cubic foot 1,728 ÷ 231, or about 7.48 US gallons. In metric, one cubic meter is exactly 1,000 liters, and one US gallon is exactly 3.785411784 liters. These definitions come from the National Institute of Standards and Technology's guide to units, so the conversion itself adds no error; any error comes from the measurements.
How to use the pool volume calculator
- Choose the shape: rectangle, round or oval.
- Choose US or metric units.
- Enter the length and width, or the diameter for a round pool.
- Enter the depth at the shallow end, and at the deep end if the floor slopes.
- Press Calculate to see the gallons, liters, volume, surface area and average depth.
Worked examples
A rectangular in-ground pool. A pool is 32 feet long and 16 feet wide, 3.5 feet deep at one end and 8 feet at the other. The average depth is (3.5 + 8) ÷ 2 = 5.75 feet. The volume is 32 × 16 × 5.75 = 2,944 cubic feet, and 2,944 × 7.48 is about 22,023 gallons.
A round above-ground pool. A 24-foot round pool filled to a depth of 4 feet holds π × 12² × 4, about 1,810 cubic feet, or about 13,536 gallons.
A metric pool. A pool 10 meters by 5 meters with a constant depth of 1.5 meters holds 75 cubic meters, which is 75,000 liters, about 19,813 US gallons.
How to measure your pool
- Measure the water, not the walls. Use the inside length and width, and measure depth from the floor to the water line, which is usually a few inches below the top of the wall.
- Round pools: measure straight across through the center for the diameter.
- Ovals: measure the longest and the widest points.
- Sloped floors: if the slope isn't even, for example a hopper bottom in the deep end, measure several depths and use their average as the shallow and deep values.
- Odd shapes: split a kidney or L-shaped pool into rectangles and circles, work each out, and add them together.
Why the volume matters
Pool chemical labels give doses per number of gallons, so an accurate volume keeps chlorine, pH adjusters and shock treatments in the right range. Too little leaves the water unsafe or cloudy; too much wastes money and can irritate skin and eyes. Pump and filter sizes are usually chosen so the whole volume passes through the filter several times a day, and heater sizing depends on how much water you need to warm. When you fill a pool from a hose, the volume divided by the flow rate tells you roughly how long it will take.
Related calculators
To turn gallons into other units, use the volume converter. For tanks and other solids, the volume and surface area calculator covers boxes, cylinders and spheres, and the area and perimeter calculator helps with the deck around the pool.
Filling and topping up
Knowing the volume also tells you how long a fill will take. Garden hoses vary widely, so time how long your hose takes to fill a 5-gallon bucket: if it takes one minute, the hose delivers about 5 gallons a minute, and a 13,536-gallon round pool would take about 2,700 minutes, or roughly 45 hours, to fill. For topping up after evaporation or splash-out, work out the volume of the missing layer: the water surface area multiplied by the drop in level. A 32 by 16 foot pool that has lost 2 inches, or about 0.17 feet, needs about 512 × 0.17 = 87 cubic feet, roughly 650 gallons, to bring it back up.
Gallons or liters on product labels
Pool products sold in the United States usually give doses per 10,000 gallons, while many other countries use liters or cubic meters. If a label uses a different unit from your result, switch the calculator's units or use the second row of the results, which always shows the other system.
Common mistakes
- Using the wall height as the depth. Pools are rarely filled to the very top.
- Using the diameter as the radius. The circle formula uses half the diameter.
- Ignoring the slope. Using only the deep-end depth can overstate the volume by a third or more.
- Mixing feet and inches. Convert a depth of 54 inches to 4.5 feet before entering it.
What next
Use this often? Add Pool Volume to your Home screen.
Frequently asked questions
How does a pool volume calculator work?
It multiplies the water surface area by the average depth, then turns cubic feet into gallons (about 7.48 per cubic foot) or cubic meters into liters.
How many gallons is a 24-foot round pool?
Filled to 4 feet deep, about 13,536 gallons.
How do I measure a pool with a sloped floor?
Measure the shallow and deep ends. The calculator uses their average depth.
How many gallons are in a cubic foot?
About 7.48 US gallons, because a gallon is exactly 231 cubic inches.
Can I use meters and liters?
Yes. Choose Metric to enter meters and get liters, with US gallons shown too.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.