Saved

Press the star next to a tool's name to save it.

All my tools

Pool Salt Calculator

Use this pool salt calculator to work out how much salt to add to a saltwater pool, or how much water to replace if the level is too high, from the volume and ppm.

Restored your last values ·

ppm
ppm

Enter the volume of the pool and the salt level that your chlorine generator shows, in parts per million. The calculator gives the salt to add to reach the target, or the water to drain and replace if the level is too high.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the pool volume and the current salt level, then press Work out the salt.

See full result

A pool salt calculator tells you how much salt to add to a saltwater pool, or how much water to replace if there is too much salt. Enter the volume of the pool, the current salt level and, if you like, the level you want, and the calculator gives the salt in pounds or kilograms, or the volume of water to drain. It uses simple arithmetic on the volume and the ppm, with the target range taken from a manufacturer's manual. It runs in your browser and nothing you enter is sent anywhere.

How to use the pool salt calculator

  1. Choose US or Metric units.
  2. Enter the volume of your pool.
  3. Enter the current salt level in parts per million, as read from your chlorine generator or test kit.
  4. Leave the target blank for 3,200 ppm, or enter your own, and press Work out the salt.

What ppm means

For water, one part per million is the same as one milligram per litre. [2] A level of 3,200 ppm therefore means 3,200 milligrams, or 3.2 grams, of salt in every litre. Hayward's owner's manual gives an ideal range of 2,700 to 3,400 ppm, with 3,200 ppm optimal. [1] You can read the current level from a test kit or from the salt display of a chlorine generator. The calculator tells you when the current level is inside that range.

Adding salt

When the level is below the target, the salt needed is the difference in ppm times the volume of the pool in litres, which gives milligrams. The calculator changes this into kilograms or pounds. Our own worked example is a pool of 100 gallons at 2,000 ppm raised to 3,200 ppm: the difference of 1,200 ppm over about 378.5 litres is about 454 grams, which is 1 pound.

Lowering the level

When the level is above the target, you must replace some of the water with fresh water. Hayward's manual says the only way to lower the salt concentration is to drain part of the pool and refill it with fresh water. [1] Our own example is 100 gallons at 4,000 ppm, with a target of 3,200 ppm, and the answer is to replace 20 gallons. This is the share 1 minus 3,200 divided by 4,000, which is 20 percent. The calculator shows the volume and the percentage. Drain and refill in a single step, and mix well before you test again.

Starting from fresh water

Two more examples start with no salt in the water. A pool of 10,800 gallons needs about 288 pounds, or 131 kilograms, to reach 3,200 ppm, and a pool of 15,000 gallons needs about 401 pounds, or 182 kilograms. You can check them by entering the volume and a current level of 0. Be aware that there may already be some salt in your pool from earlier chemical use, so test before you add any. [1]

Why the level matters

A low salt level reduces the efficiency of a salt chlorine generator and results in low chlorine production. A high level can make it shut down, and the water may taste salty at about 3,500 to 4,000 ppm. [1] Running a cell with too little salt can also strip its coating, which means an expensive replacement. [3] Keep the level within the range your equipment's maker gives, which may be different from the range above.

Adding the salt safely

Turn the circulation pump on and add the salt directly to the pool. Brush it around to speed up dissolving, and do not let it pile up on the bottom. Run the filter pump for 24 hours so that the salt spreads evenly, and wait before you test the level again. [1] Use plain sodium chloride that is more than 99 percent pure; Hayward says not to use rock salt, iodized salt or salt with anti-caking additives. [1] Follow the instructions of your chlorine generator for the level it needs.

Reading the result

The calculator shows the salt to add, in pounds for US units and in kilograms for metric units. If the level is too high, it shows the volume of water to drain and the share of the pool that this is. If the current level is already at the target, it says so. A note tells you when the current level is inside the manufacturer's range of 2,700 to 3,400 ppm, so that you can see whether you need to do anything at all.

Metric and US units

In US units, the volume is in gallons and the salt in pounds, and the calculator converts gallons to litres first, using 3.785 litres to the gallon, and kilograms to pounds at 2.205 pounds to the kilogram. In metric units, the volume is in litres and the salt in kilograms, so the result is the difference in ppm times the number of litres, divided by one million. The two systems give the same answer for the same pool.

Choosing a target

Hayward treats 3,200 ppm as optimal, and the calculator uses it when you leave the target blank. Different chlorine generators ask for different levels, and some have a narrower range, so check the manual for your equipment. Enter your own target if it is different from the default. A small change in the target changes the salt by a proportional amount.

How often to check

Salt does not evaporate, so the level falls mainly when water is lost by splashing, backwashing or draining and is replaced with fresh water. [1] Test the level from time to time, and after a lot of rain or a refill, and add salt only when the level has dropped. Adding too much salt is harder to fix than adding too little, so add in stages.

Common mistakes

  • Using the wrong volume. Use the real volume of the water, not the size of the pool shell.
  • Adding all the salt at once. Add in stages and test.
  • Mixing units. Choose US or Metric first.
  • Forgetting what is already in the water. Read the current level before you add.

What next

Use this often? Add Pool Salt to your Home screen.

Frequently asked questions

What is a pool salt calculator?

A tool that works out how much salt to add to a pool, or how much water to replace, from its volume and salt level.

What is the ideal salt level for a pool?

One manufacturer's manual gives an ideal range of 2,700 to 3,400 ppm, with 3,200 ppm optimal. Check the manual for your own equipment.

How much salt for a 10,800 gallon pool?

About 288 pounds (131 kg) to reach 3,200 ppm from fresh water.

What if the salt level is too high?

Replace part of the water with fresh water. From 4,000 ppm to 3,200 ppm, that is 20 percent.

What does ppm mean?

For water, one part per million is one milligram of salt per litre.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Everyday Life Tools