Saved

Press the star next to a tool's name to save it.

All my tools

Pde Sipm Calculator

Use this pde sipm calculator to convert the responsivity of a silicon photomultiplier to its photon detection efficiency, or back, from gain, crosstalk, afterpulsing and wavelength.

Restored your last values ·

%
%
nm
A/W
%

Enter the gain, the crosstalk and afterpulsing probabilities in percent, the wavelength in nanometres and either the responsivity in amperes per watt to find the photon detection efficiency, or the efficiency to find the responsivity.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to find and fill in the boxes, then press Calculate.

See full result

A pde sipm calculator converts between the responsivity of a silicon photomultiplier and its photon detection efficiency. Enter the gain, the crosstalk and afterpulsing probabilities and the wavelength, and it works out the efficiency from the responsivity, or the responsivity from the efficiency.

How to use the pde sipm calculator

  1. Choose PDE or responsivity as the result.
  2. Enter the gain, the crosstalk and afterpulsing in percent, and the wavelength in nanometres.
  3. Enter the responsivity in A/W, or the PDE in percent.
  4. Press Calculate.

What a silicon photomultiplier is

A silicon photomultiplier, or SiPM, is a light sensor made of many tiny avalanche cells that fire when a photon arrives. The Wikipedia article says that its photon detection efficiency ranges from 20 to 50 percent, depending on the device and the wavelength, and that its gain is similar to that of a photomultiplier tube [1]. These numbers set the scale of everything on this page.

What the PDE means

The photon detection efficiency is a measure of the sensitivity of the SiPM, and it can be found from its responsivity. A PDE of 35 percent means that roughly 35 of every 100 photons that reach the sensor are detected. The responsivity, in turn, is the photocurrent that the sensor produces for each unit of optical power, in amperes per watt [3]. The conversion from responsivity to quantum efficiency is given on Wikipedia's quantum efficiency page [2].

The formula

The tool uses PDE = R h c ÷ (e λ G (1 + P_XT)(1 + P_AP)), where R is the responsivity, λ the wavelength, G the gain, P_XT the crosstalk probability and P_AP the afterpulsing probability, and its rearrangement for the responsivity. It extends the standard conversion from responsivity to quantum efficiency, QE = (R ÷ λ) × (h c ÷ e) [2], by dividing by the gain and by the crosstalk and afterpulsing factors; that extension is our own working. The constants h, c and e are the exact SI values, from the 2019 revision of the SI [4], and they combine into h c ÷ e = 1.2398 × 10⁻⁶ volt metres.

Gain, crosstalk and afterpulsing

In this tool the gain is the charge created for each detected photon, in units of the electron charge. Crosstalk happens when one photon produces a signal equal to two or more photons. Afterpulsing happens when carriers are trapped in defects in the silicon and released later, which creates an extra signal soon after the first. These plain-language definitions are our own summary. The Wikipedia article defines afterpulsing as the probability of spurious second pulses after a single photon arrives, and gives a range of 3 to 30 percent [1].

A worked example

Take a gain of 1,000,000, a crosstalk of 20 percent, afterpulsing of 4 percent, a wavelength of 420 nanometres and a responsivity of 150,000 A/W. Working it by hand: the conversion factor h c ÷ (e λ) is 2.952 volts, the product with R is 442,850 and the divisor is 1,248,000, so the efficiency is 35.48 percent.

Units of the responsivity

The responsivity is measured in amperes per watt [3]. The tool takes the value in A/W, which makes the formula consistent, because h c ÷ (e λ) then has the unit of volts and the product with R is a pure number. If you use a different unit for the responsivity, convert it before you use the tool. This check of the units is our own working.

Solving for the responsivity

Choose responsivity and enter the PDE as a percentage, and the tool rearranges the formula: R = PDE × G (1 + P_XT)(1 + P_AP) ÷ (h c ÷ (e λ)). With the numbers of the example and a PDE of 35.48 percent, you get about 150,000 A/W back. This direction is useful when a data sheet quotes the efficiency and you need the current output for a given amount of light.

Why the wavelength matters

The efficiency of a SiPM changes with wavelength, so a PDE figure only makes sense together with the wavelength at which it was measured [1]. The wavelength enters this formula through the energy of each photon, h c ÷ λ. For the same responsivity, a shorter wavelength means fewer photons for each watt of light, so each detected photon must account for more current, and the PDE comes out higher. Always enter the wavelength at which the responsivity was measured.

Checking the answer

A PDE above 100 percent is not possible, and the tool warns you if it gets one. The usual cause is a gain entered in the wrong unit, a responsivity in the wrong unit, or a wavelength given in micrometres instead of nanometres. Typical values quoted for these sensors are in the tens of percent [1], so a result far from that range is worth a second look at the data sheet.

Limits of the conversion

The tool only reorganises the formula above. It does not model temperature, overvoltage, dark counts or saturation, all of which change real sensors. Use it to compare data sheets or to check a quoted value, and use the manufacturer's measured curves for any design decision.

Common mistakes

  • Entering the gain as a power of ten. Type the full number, for example 1000000.
  • Entering percentages as fractions. Crosstalk, afterpulsing and PDE are in percent here.
  • Using the wrong wavelength. Use the wavelength at which the responsivity was measured, in nanometres.
  • Forgetting the correction factors. Crosstalk and afterpulsing both add to the gain.

What next

Use this often? Add Pde Sipm to your Home screen.

Frequently asked questions

What is a pde sipm calculator?

A tool that converts between the responsivity of a silicon photomultiplier and its photon detection efficiency.

What is the formula for the PDE of a SiPM?

PDE = R h c ÷ (e λ G (1 + P_XT)(1 + P_AP)), with the responsivity R, the wavelength λ, the gain G and the crosstalk and afterpulsing probabilities.

What is typical PDE of a SiPM?

The Wikipedia article quotes 20 to 50 percent, depending on the device and the wavelength.

What units does the responsivity have?

Amperes per watt, which is the standard unit of responsivity.

Why does the calculator warn about a PDE over 100 percent?

Because an efficiency cannot exceed 100 percent, so such a result points to a wrong input or unit.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools