This MOSFET calculator finds the drain current of an n-channel enhancement MOSFET from its threshold voltage, its K parameter and the gate-source and drain-source voltages. It tells you whether the transistor is in cut-off, in the triode region or in saturation, gives the transconductance, and can also find K and the threshold voltage with body effect.
How to use the MOSFET calculator
- Choose what to find.
- Enter the threshold voltage, the K parameter and the two voltages.
- Press Calculate.
The three regions
A MOSFET works in one of three regions, set by the gate-source voltage V_GS and the drain-source voltage V_DS. Below the threshold voltage V_T there is no channel, and the device is in cut-off. Above it, the device is in the triode, or linear, region when V_DS is below V_GS − V_T, and in saturation when V_DS is equal to or above V_GS − V_T [1]. The calculator finds the region first, and then uses the right equation.
The K parameter
This calculator writes the current with a single parameter K, defined as K = ½ × (W ÷ L) × µN × Cox, where W is the channel width, L the length, µN the electron mobility and Cox the oxide capacitance per unit area. It is a regrouping of the terms in the equations on Wikipedia [1]. It comes from the device geometry and the process, and can be taken from a data sheet. Deriving K from a single data sheet point depends on the model used, so enter a K that you trust.
The triode equation
In the triode region, the drain current is I_D = 2K (V_GS − V_DS/2 − V_T) V_DS. Wikipedia gives the equivalent form I_D = µnCox (W/L) ((V_GS − V_th) V_DS − V_DS²/2) [1]. With K = ½ (W/L) µn Cox the two are the same expression, which we checked by expanding it. The current rises almost in proportion to V_DS at first, so that the transistor acts like a resistor controlled by the gate.
The saturation equation
In saturation, the drain current is I_D = K (V_GS − V_T)². Wikipedia writes it as µnCox/2 × W/L × (V_GS − V_th)² and adds a factor 1 + λ V_DS for channel-length modulation [1]. This calculator leaves that factor out, so the current does not depend on V_DS in saturation. At the boundary, V_DS = V_GS − V_T, the triode and saturation equations give the same value, which makes a good check.
A worked example
As an example, take a small n-channel transistor with V_T = 2 volts and K = 0.05625, at V_GS = 8 volts and V_DS = 5 volts. The overdrive voltage is 6 volts, above V_DS, so the device is in the triode region, and I_D = 2 × 0.05625 × (8 − 2.5 − 2) × 5 = 1.969 amperes. With V_DS = 10 volts, the device is in saturation and I_D = 0.05625 × 36 = 2.025 amperes. Enter 2, 0.05625, 8 and 5 to see the first result.
Transconductance
The transconductance g_m tells you how much the drain current changes for each volt on the gate. Wikipedia gives, for saturation, g_m = 2 I_D ÷ (V_GS − V_th) [1], which for this model is 2K (V_GS − V_T). In the triode region, taking the derivative of the triode equation with respect to V_GS gives 2K V_DS, our own working. In the example above, g_m is 0.5625 siemens in the triode region and 0.675 in saturation.
Finding K
In the second mode, K is found from the ratio of the width to the length and the product µN Cox, the process transconductance parameter, which data sheets and textbooks list in amperes per volt squared. For W/L = 20 and µN Cox = 100 microamperes per volt squared, K = ½ × 20 × 0.0001 = 0.001 amperes per volt squared. A wider or shorter channel gives a larger K, and so more current for the same voltages.
Threshold voltage and body effect
The third mode covers the case when the source is not at the same potential as the body. The threshold with body effect is V_T = V_T0 + γ (√(2φF + V_SB) − √(2φF)), where V_T0 is the threshold at zero source-body voltage and γ is the body-effect parameter [1][2]. With V_T0 = 0.7 volts, γ = 0.4, 2φF = 0.8 volts and V_SB = 2 volts, the threshold rises to 1.0116 volts. This mode also serves as a MOSFET threshold voltage calculator for the body effect.
Why we do not calculate V_T from doping
The threshold at zero body bias, V_T0, depends on the doping and the oxide capacitance, which are rarely known for a given part [2]. This calculator therefore takes V_T0 from the data sheet and does not compute it from the doping. That choice is ours, and it keeps the result tied to a measured value of the part.
Limits of the model
The calculator covers n-channel enhancement devices and the ideal square-law model. It ignores leakage below the threshold, channel-length modulation, velocity saturation in short channels, and temperature. A P-channel device uses the same equations with the signs reversed. Use the result as a first estimate, and check the part's output curves in the data sheet before you rely on a design.
Common mistakes
- Using a K that comes from a different equation. K here is ½ × W/L × µN Cox.
- Entering a negative V_DS. This model is for an n-channel device with V_DS of 0 or more.
- Treating the result as exact. Real parts have channel-length modulation.
- Mixing millivolts and volts. Enter volts.
What next
Use this often? Add Mosfet to your Home screen.
Frequently asked questions
What is a MOSFET calculator?
A tool that finds the drain current and operating region of a MOSFET from its voltages and parameters.
When is a MOSFET in saturation?
When V_GS is above V_T and V_DS is equal to or above V_GS − V_T.
What is the MOSFET drain current in saturation?
I_D = K (V_GS − V_T)², with K = ½ (W/L) µN Cox.
What is the body effect?
A rise of the threshold voltage when the source is above the body potential.
Does this MOSFET calculator include channel-length modulation?
No. It is the ideal square-law model.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.