A mash water calculator tells an all-grain brewer how much water to heat for the mash and how hot it should be. If the strike water is too cool the mash settles below its target rest. If it is too hot you can damage the enzymes in the grain. This page uses Palmer's infusion equation for the temperature and a simple water to grain ratio for the volume, then works out the sparge water for your pre-boil target.
How to use this mash water calculator
- Choose US (pounds, quarts, Fahrenheit) or Metric (kilograms, litres, Celsius).
- Enter the weight of the crushed grain.
- Enter the water to grain ratio. Leave it blank for 1.5 quarts per pound or 3 litres per kilogram.
- Enter the temperature of the dry grain, which is usually room temperature, and the mash temperature you want.
- Optionally add your pre-boil volume to get the total water and the sparge volume, and press Calculate.
How the strike water temperature is worked out
Palmer's How to Brew gives the dry grain infusion equation as the strike temperature equal to 0.4 divided by R, times the target mash temperature minus the dry grain temperature, plus the target mash temperature [1]. The constant reflects that grain has about 40 percent of the heat capacity of water [1]. R is the water to grain ratio in litres per kilogram. When you work in quarts per pound the calculator multiplies the ratio by 2.0864, our own unit conversion, to get litres per kilogram. The equation only uses a temperature difference, so it works the same in Fahrenheit and Celsius.
Strike volume and the sparge
The strike volume is the grain weight times the water to grain ratio. How to Brew recommends a ratio of 1.5 to 2 quarts per pound, or 3 to 4 litres per kilogram [1]. A thinner mash is easier to stir and a thicker one holds heat better. For the sparge, the calculator adds your pre-boil volume to the water the grain soaks up and subtracts the strike water. We default the absorption to 0.125 gallons per pound, about 1.04 litres per kilogram, a common rule of thumb that you can change to match your own system. Equipment such as a mash tun with dead space also keeps some liquid back, so test your own numbers.
Worked example: 10 pounds of grain
Mash 10 pounds of grain at 1.5 quarts per pound. Strike volume is 15 quarts, which is 3.75 gallons. The ratio is 3.13 litres per kilogram. With grain at 70 °F and a 152 °F target, the strike temperature is 0.4 divided by 3.13 times 82 plus 152, or 162.5 °F. If the pre-boil volume is 6.5 gallons and the grain absorbs 1.25 gallons, the total water is 7.75 gallons, so the sparge is 4 gallons. In metric, 5 kilograms of grain at 3 litres per kilogram needs 15 litres at 73.3 °C to reach 67 °C from 20 °C.
| Water to grain (qt/lb) | Strike water above mash target for 70 °F grain and a 152 °F mash |
|---|---|
| 1.25 | 12.6 °F |
| 1.5 | 10.5 °F |
| 2 | 7.9 °F |
| 3 | 5.2 °F |
A thicker mash needs hotter strike water, which is why the first row is the highest.
Tips for hitting your mash temperature
- Preheat the mash tun with hot water for a few minutes. A cold vessel steals heat from the strike water, so many brewers aim a little higher.
- Stir the mash well and check the temperature in several places before you trust a single reading.
- Do not let the strike temperature go above 212 °F. The calculator warns you if the ratio is too thick for your grain temperature.
- Write down what your system really does and adjust the strike temperature by a degree or two next time.
Why strike temperature matters
Enzymes in malted grain turn starch into sugars, and each enzyme works best in a narrow band of temperature. A lower mash temperature around 148 to 150 °F tends to make a drier, more fermentable wort. A higher mash around 156 to 158 °F leaves more dextrins and a fuller body. Those ranges are a common brewing guide and our own summary, not a figure from the source. Because the whole mash is set by the first infusion, an accurate strike temperature helps you hit the rest you want without having to add hot or cold water later.
Thick mash or thin mash
A thick mash, near 1.25 quarts per pound, needs hotter strike water but keeps its heat well and gives a strong enzyme action. A thin mash, near 2 quarts per pound, is easier to stir and to drain. You can play with the ratio in the calculator and watch the strike temperature change. The warning appears when the strike water would be above boiling, which means you need more water or a warmer grain bill.
If you brew in a bag or use a recirculating system, volumes and losses differ from a simple tun. Treat the sparge figure as a starting point and write down what happens in practice.
Common mistakes
- Mixing the ratio units: 1.5 quarts per pound is not 1.5 litres per kilogram.
- Entering the grain temperature after it has warmed up in a heated room.
- Forgetting that the target is the mash temperature, not the strike temperature.
- Using the mash water calculator output without allowing for the tun, boil-off and dead space.
What next
Use this often? Add Mash Water V to your Home screen.
Frequently asked questions
How does a mash water calculator find the strike water temperature?
It uses Palmer's equation: 0.4 divided by the water to grain ratio in litres per kilogram, times the gap between the target and the grain temperature, plus the target temperature.
How much water should I use per pound of grain?
How to Brew recommends 1.5 to 2 quarts per pound, which is about 3 to 4 litres per kilogram. Thicker mashes hold temperature better and thinner mashes stir more easily.
How is the sparge water calculated?
The calculator adds your pre-boil volume to the water the grain absorbs and subtracts the strike water you already used. If the answer is zero or less, no sparge is needed.
How much water does the grain absorb?
A common rule of thumb is about 0.125 gallons per pound, or 1.04 litres per kilogram. Your system may differ, so you can type your own figure in the absorption box.
Why is my mash cooler than the calculator says?
A cold mash tun, a loose lid and a thin mash all lose heat. Preheat the tun, stir, and raise the strike temperature a degree or two next time.
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.