Saved

Press the star next to a tool's name to save it.

All my tools

Priming Sugar Calculator

Use this priming sugar calculator to find how much corn sugar or table sugar to add when bottling beer, from the batch size, the target CO2 volumes and the CO2 already in the beer.

Restored your last values ·

volumes
volumes

Enter your batch size, the carbonation you want in volumes of CO2, and the CO2 already dissolved in the beer after fermentation. Pick the sugar you will use. The residual CO2 depends on how warm the beer fermented, so look it up on a carbonation chart or calculator.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Fill in the boxes and press Calculate sugar.

See full result

A priming sugar calculator works out how much sugar to add to a batch of beer at bottling so that it carbonates to the level you want. Enter your batch size, the volumes of CO2 you are aiming for and the CO2 already in the beer, choose the sugar, and the calculator gives the weight to add, in ounces or grams. It runs in your browser and nothing you enter is sent anywhere.

Why priming sugar needs a calculation

Brew Your Own explains that many recipes tell you to add a standard amount of priming sugar, usually 3 to 5 ounces of corn sugar, or two thirds to three quarters of a cup. The article calls this a dangerous over-simplification. No matter how flat the beer looks and tastes after fermentation, it still holds some dissolved CO2, and how much depends mainly on how warm the beer fermented. Priming sugar needs to supply only the difference between the carbonation you want and the CO2 that is already there.

How to use the priming sugar calculator

  1. Choose US or Metric units.
  2. Pick your priming sugar: corn sugar (anhydrous or monohydrate) or table sugar.
  3. Enter the batch size.
  4. Enter the target carbonation in volumes of CO2, and the CO2 already in the beer.
  5. Press Calculate sugar.

Volumes of CO2

Carbonation is measured in volumes of CO2: the volume the gas would fill at standard temperature and pressure, for each volume of beer. A beer with 2.5 volumes holds two and a half times its own volume in CO2. The BYO article lists ranges for different styles: American ales 2.2 to 3.0, British ales 1.5 to 2.2, German weizens 2.8 to 5.1, Belgian ales 2.0 to 4.5, European lagers 2.4 to 2.6 and American lagers 2.5 to 2.8 volumes.

How much CO2 each sugar gives

The article gives the yields for a 5 gallon (19 litre) batch. One ounce (28 g) of glucose gives about 0.37 volumes of CO2, one ounce of glucose monohydrate gives about 0.34 volumes, and one ounce of cane or beet sugar, which is sucrose, gives about 0.39 volumes. The difference is that corn sugar comes in an anhydrous form and a hydrated form, and the hydrated form carries some water, so you need a little more of it. Check the label to see which you have.

The formula

The sugar needed is the CO2 to add, in volumes, divided by the rate for your sugar, then scaled to your batch. For a 5 gallon batch the weight in ounces is the CO2 to add divided by the volumes per ounce. For another size, multiply by the batch size in gallons divided by 5. The calculator converts litres to gallons and ounces to grams for you.

Worked example

The BYO article describes a British-style bitter fermented at 65 °F with 0.894 volumes of CO2 already in the beer, aiming for the bottom of the British range at 1.5 volumes. You need to add 0.606 volumes. For glucose, that is 0.606 divided by 0.37, which is about 1.64 ounces, or 46 grams, in a 5 gallon batch. The article's own figures give 1.6 ounces (45 g) of glucose, 1.8 ounces (51 g) of glucose monohydrate and 1.5 ounces (43 g) of sucrose for 0.6 volumes. A stronger American ale at 2.5 volumes with the same residual would need 1.606 divided by 0.37, which is about 4.3 ounces or 123 grams of glucose.

Finding the residual CO2

Residual CO2 is hard to measure at home. The BYO article says carbonation priming charts and online calculators give a close approximation from the fermentation temperature, and its chart gives 0.894 volumes for the bitter fermented at 65 °F. The warmer the fermentation, the less CO2 stays dissolved, and the more sugar you need. The article adds that these numbers do not allow for beer that has sat at a higher temperature after fermentation, so adjust if that applies to you.

Adding the sugar

The article suggests dissolving the sugar in about a cup of water, boiling it and cooling it under a tight cover before adding it to the beer, because sugar added directly can make zones that are too sweet for the yeast. It stresses weighing the sugar on a scale, and having healthy yeast in the beer so that the sugar ferments fully. Mix gently to avoid taking up oxygen.

Safety

Priming adds fermentable sugar to a sealed bottle, so too much can cause over-carbonation and bottles that foam over or burst. Only bottle beer that has finished fermenting, use bottles made to hold pressure, and keep them in a safe place while they condition.

Kegging instead of bottling

The BYO article notes that you can prime a keg exactly as you would bottles, but that there is a simpler way: force carbonate the beer with CO2 from a cylinder. First decide how many volumes of CO2 you want. This calculator is for bottles and for priming a keg with sugar, where the beer is carbonated by its own yeast.

Sugar by weight, not by cups

The article says that if you have gone to the trouble of calculating the amount of sugar, you should weigh it exactly. A cup of sugar varies in weight with how it is packed, and corn sugar and table sugar have different densities. Use a scale that is accurate to a gram or to a tenth of an ounce.

Common mistakes

  • Using a standard scoop for every beer. The right amount depends on the batch size, the style and the residual CO2.
  • Ignoring the residual CO2. Even flat beer holds some.
  • Mixing up sugars. Corn sugar anhydrous, corn sugar monohydrate and table sugar need different weights.
  • Measuring by volume. Weigh the sugar.

What next

Use this often? Add Priming Suga to your Home screen.

Frequently asked questions

What is a priming sugar calculator?

A tool that works out how much sugar to add to beer at bottling so the yeast makes the carbonation you want.

How much priming sugar do I need for 5 gallons?

It depends on the style and the CO2 already in the beer. For 1.5 volumes with 0.894 already dissolved, about 1.6 ounces (46 g) of corn sugar.

Which sugar gives the most CO2?

By weight, cane sugar (sucrose) gives about 0.39 volumes per ounce in 5 gallons, anhydrous corn sugar 0.37 and corn sugar monohydrate 0.34.

Why do I need to know the residual CO2?

Beer still holds some CO2 after fermentation, so you add only the difference between the target and what is there. Warmer fermentations leave less.

How many volumes of CO2 should my beer have?

BYO gives ranges, for example British ales 1.5 to 2.2, American ales 2.2 to 3.0 and European lagers 2.4 to 2.6 volumes.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Unit Converters