Saved

Press the star next to a tool's name to save it.

All my tools

Log Reduction Calculator

Use this log reduction calculator to turn before and after levels into a log reduction and a percent reduction, or to find the level left after a given log reduction.

Restored your last values ·

Enter the level before and after a treatment, such as 580 and 0.725 ppm, to get the log reduction and percent reduction. Or enter a percent reduction to get the log reduction, or a starting level and log reduction to get the level that remains.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Choose what to work out, fill in the boxes, then press Calculate.

See full result

A log reduction calculator turns the levels of contamination before and after a treatment into a log reduction and a percent reduction. A 1-log reduction means 90 percent of the contaminant is gone, a 2-log reduction means 99 percent, and a 3-log reduction means 99.9 percent.

How to use the log reduction calculator

  1. Choose what to work out: the log reduction from before and after levels, the log reduction from a percent, or the final level from a log reduction.
  2. Enter the values, using the same unit for both levels.
  3. Press Calculate.

The definition

The Wikipedia article on log reduction defines it as the common logarithm of the ratio of the levels of contamination before and after the process, so an increase of 1 corresponds to a reduction in concentration by a factor of 10.[1] In general, an n-log reduction means the remaining concentration is only 10 to the power minus n times the original.[1] With c before and c after, the page gives R = log10(c before) − log10(c after) = −log10(c after ÷ c before).[1] The page adds that the units do not matter as long as both levels use the same unit.[1]

Percent reduction

The page gives the percent reduction as P = 100 × (c before − c after) ÷ c before.[1] A whole-number log reduction corresponds to a percentage with that many leading nines, as long as it is at least 10 percent.[1] The common cases on the page are 1-log for 90 percent, 2-log for 99 percent, 3-log for 99.9 percent, 4-log for 99.99 percent and 5-log for 99.999 percent.[1] It also says that a 0-log reduction is no reduction at all.[1]

The worked example from the page

The page takes 580 ppm before and 0.725 ppm after. Then R = −log10(0.725 ÷ 580) = −log10(0.00125), about 2.903. Rounded down it is 2, so a 2-log reduction is achieved.[1] The percent reduction is 100 × (580 − 0.725) ÷ 580 = 99.875, which the page describes as better than a 99 percent reduction but not quite a 99.9 percent reduction.[1] Enter 580 and 0.725 and the calculator shows 2.9031, a whole-number 2 and 99.875%. It also shows the factor of reduction: the concentration fell 800 times.

Why the number is rounded down

The page says the value of R is rounded down to the desired precision, usually a whole number.[1] Rounding down avoids claiming a 3-log reduction when only 2.9 logs were achieved. The calculator shows both the exact value and the rounded-down whole number. We add a tiny tolerance so that a value such as 99.9 percent, which is exactly 3 logs, is not shown as 2 because of computer rounding.

From a percent to a log, and back

The inverse formulas follow from the page's definitions and are our own working. The log reduction for a percent reduction P is −log10(1 − P ÷ 100), so 99.9 percent gives 3 and 99 percent gives 2. The level left after a log reduction of R is the starting level times 10 to the power minus R, so a starting level of 1,000,000 with a 3-log reduction leaves 1,000. The percent reduction in that case is 99.9 percent. The page does not state these forms, but they give the same results as its formulas.

Zero counts

If nothing is left after the treatment, the ratio is zero and its logarithm does not exist. The page does not say how to handle that case, so the calculator asks for a value instead and rejects zero. Laboratories usually report the detection limit of the method, such as 1 cell per 100 millilitres, and call the result a log reduction of at least that value. Using the detection limit gives the largest log reduction that can honestly be claimed. This advice is our own working, not from the page.

Using log reductions in practice

Disinfection, water treatment and food safety often set a target log reduction. Because each log is a tenfold drop, two treatments that give 2 logs each combine to 4 logs, assuming each acts on what is left. That is our own use of the definition, and real processes may have limits. The page itself does not describe disinfection targets or other standards, so check the rules that apply to your process.

A short table to remember

Each extra log is another factor of 10. A 1-log reduction leaves one tenth, 2 logs leave one hundredth and 3 logs leave one thousandth. Between whole numbers, 0.5 log is a reduction by a factor of about 3.16 or roughly 68 percent, and 1.5 logs is a factor of about 31.6 or about 96.8 percent. These intermediate figures are our own calculations from the definition and show why half-logs are not simply halfway in percent terms. The percent scale flattens quickly: going from 99 to 99.9 percent looks small but is a whole log, a tenfold improvement.

Reporting a result

State the starting level, the final level, the unit and the log reduction, rounded down to a whole number as the page describes, for example: from 580 ppm to 0.725 ppm, a 2-log reduction. Say how the measurement was made and mention the detection limit if the final level was close to it.

Common mistakes

  • Mixing units. Both levels must be in the same unit.
  • Confusing log and percent. 99 percent is 2 logs, not 99 logs.
  • Entering zero. Use the detection limit.

What next

Use this often? Add Log Reductio to your Home screen.

Frequently asked questions

What is a log reduction calculator?

A tool that finds the common-logarithm drop in contamination from the levels before and after a treatment, and the matching percent reduction.

What is the log reduction formula?

R = log10(before) − log10(after) = −log10(after ÷ before).

What percent is a 3-log reduction?

99.9 percent. A 1-log reduction is 90 percent, 2-log is 99 percent, 4-log is 99.99 percent and 5-log is 99.999 percent.

How do I find the log reduction from a percent?

Use −log10(1 − P ÷ 100), where P is the percent reduction. For 99.9 percent it is 3.

What if the level after is zero?

The logarithm of zero does not exist. Use the detection limit of your test and report the result as at least that log reduction.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools