This internet speed test measures how fast your connection is right now. Press the button and it measures your latency, then your download speed, then your upload speed, and shows the results in megabits per second. The test runs in your browser and exchanges test data with Cloudflare's public speed-test servers, using the same endpoints and a similar sequence of requests to the ones in Cloudflare's open-source speed test.
How to use the internet speed test
- Close other downloads, streams and video calls on your network.
- If you can, connect with a cable, or stand close to your Wi-Fi router.
- Press Start the test and wait until it finishes, about half a minute.
- Read your download speed, upload speed, latency and jitter.
What the numbers mean
The download speed is how fast data comes to your device, which matters for streaming, browsing and downloading. The upload speed is how fast data goes out, which matters for video calls, sending large files and backing up photos. Both are shown in megabits per second, a unit of speed, and a megabyte is eight megabits, so a speed of 80 megabits per second is 10 megabytes per second. Latency is how long a small message takes to make a round trip to the server, in milliseconds. The Wikipedia page on ping describes it as the round-trip time of a message that is sent out and echoed back. Jitter is the variation in latency from one message to the next, which the Wikipedia page on jitter describes as packet delay variation. A connection with a constant delay has no jitter.
How the test works
The test follows the order that Cloudflare's speed test uses. First it sends a series of tiny requests to measure the latency. Then it downloads files of growing size, from 100 kilobytes up to 25 megabytes, and then it uploads data of growing size, up to 5 megabytes. Bigger files are skipped once a size takes a second or more, since a longer test would add little. The speed for each file is the amount of data divided by the time that it took, and the figure that is shown is the 90th percentile of all of the measurements, which is the method that Cloudflare's own test uses by default. A test therefore moves up to about 60 megabytes of data.
Why your result may be lower than your plan
The speed on your plan is a maximum, and the Wikipedia page on bandwidth notes that real throughput is lower than the capacity of a channel, because protocols, encryption and lost packets add overhead. Other things matter too. A weak Wi-Fi signal or a crowded network can slow you down, other devices may be using your connection at the same moment, and an old router or cable can limit your speed. The test servers are far away for some people, and a distant server adds delay. For the most reliable number, connect with a cable and repeat the test a few times, and look at the middle of the results.
What is a good speed
It depends on what you do. Browsing and email need little. Streaming video in high definition and video calls need more, and a household where several people stream, game and work at once needs more again. Rather than aim for a number, ask whether your use feels smooth. If it does not, and your test results are far below your plan, check your equipment and talk to your provider. High latency and high jitter can make calls and games feel poor even when the download speed is high.
Privacy
The test runs in your browser and sends data to Cloudflare's speed-test servers, which see your IP address as any website you visit does. The page does not record your result or send it anywhere else. Ad blockers and privacy tools may block the requests to the test servers, and if the test fails, try turning them off for this page.
Tips for a fair result
For the most useful number, run the test a few times at different times of the day, since the speed can change in the evening when more people are online. Reboot your router if the results are much lower than you expect, and test with only one device in use. If you test over Wi-Fi, note the room that you were in, so that you can compare it with a test in another room. A wired connection shows what your plan delivers, and the difference between wired and wireless shows how much your Wi-Fi costs you.
Reading latency and jitter
Latency of a few milliseconds to a few tens of milliseconds is typical for a good connection to a nearby server, and the Wikipedia page on network delay says that delays over the internet can range from a few milliseconds to several hundred. Lower is better for video calls and online games. Jitter that is small compared with the latency means a steady connection, and large jitter means that delays vary and calls may stutter. The test shows jitter as the average difference between neighbouring latency measurements.
If the test fails
If the test cannot finish, the usual cause is a blocker. Some browser extensions, networks and security software stop requests to speed-test servers. Try turning off the extension for this page, or use another browser. If your connection drops during the test, the page tells you, and you can start again.
Common mistakes
- Testing while others stream. Their traffic shares your connection.
- Reading Mbps as MB/s. Divide by eight to get megabytes per second.
- Testing over weak Wi-Fi. Move closer or use a cable.
- Judging by one test. Repeat it a few times.
What next
Use this often? Add Internet Spe to your Home screen.
Frequently asked questions
What is an internet speed test?
A test that measures how fast data moves between your device and a test server, with its download speed, upload speed, latency and jitter.
How does this speed test work?
It sends tiny requests for latency, then downloads and uploads data of growing size to Cloudflare's speed-test servers and reports the 90th percentile of the speeds.
What are Mbps?
Megabits per second. A megabyte is eight megabits, so 80 Mbps is 10 megabytes per second.
Why is my speed lower than my plan?
The plan speed is a maximum. Overhead, Wi-Fi, other devices and the distance to the server lower what you measure.
How much data does the test use?
Up to about 60 megabytes, depending on how fast your connection is.
Sources
Was this tool helpful?
What went wrong?
We only receive the reason you pick, never what you typed into the tool.
Thanks for your feedback.