Saved

Press the star next to a tool's name to save it.

All my tools

Impact Test Calculator

Use this impact test calculator to find the energy absorbed by a notched specimen in a Charpy or Izod test from the hammer's mass, pendulum length and fall and rise angles.

Restored your last values ·

°
°

Choose US or metric units. Enter the mass of the hammer, the length from the pivot to the strike centre, the angle from which it is released and the angle it reaches after breaking the specimen. A loss figure is optional.

Everything is worked out in your browser. Nothing you type is sent anywhere.

–

–

Enter the hammer mass, the pendulum length and the two angles, then press Calculate.

See full result

The impact test calculator finds the energy absorbed by a notched specimen in a Charpy or Izod pendulum test. The hammer is released from a raised position, breaks the specimen and swings up to a lower height, and the energy lost from the swing is the energy that the break took [1]. Enter the mass, the length and the two angles to get the energy and the impact speed.

How to use the impact test calculator

  1. Choose US or metric units.
  2. Enter the mass of the hammer and the length from the pivot to the strike centre.
  3. Enter the angle of fall and the angle of rise.
  4. Add an energy loss if you know it, then press Calculate.

How the test works

In a Charpy or Izod test, a heavy pendulum swings down and strikes a notched specimen. The Wikipedia article on the Charpy test says that the energy transferred to the material is inferred from the difference in height of the hammer before and after the fracture [1]. A tough material absorbs a lot of energy and the hammer rises only a little. A brittle one absorbs little and the hammer swings almost as high as it started.

The absorbed energy formula

The Wikipedia article gives the absorbed energy as K = m g (h − h′), where h is the starting height and h′ the height after the break [1]. Written with the angles, it is E = m g S (cos α − cos β) − E_l, where S is the length of the pendulum to the strike centre, β the angle of fall, α the angle of rise and E_l the energy loss. The two forms agree, because each height is S times one minus the cosine of the angle.

The heights

The initial height is h = S (1 − cos β) and the height after the break is h₁ = S (1 − cos α). The calculator shows both. They follow from the geometry of the pendulum: the bob is at a vertical distance S cos θ below the pivot at the angle θ, so that it is raised by S minus that amount. The energy is the weight of the hammer times the drop in height.

The impact velocity

The speed of the hammer at the moment of impact is V = √(2 g h), the speed of a body that has fallen through the initial height h, from energy conservation. With a fall angle of 60 degrees on a 1 m pendulum, the hammer has dropped 0.5 m and hits at about 3.13 m/s. Standards set the strike speed within a range, so check it against the standard that applies to your material and machine.

A worked example

Take a pendulum of 1 m, a hammer of 440 g, a fall angle of 60 degrees and a rise angle of 30 degrees. The initial height is 0.5 m and the rise height is 0.13397 m. The absorbed energy is 0.44 × 9.80665 × 1 × (cos 30° − cos 60°) = 1.5794 J, and the impact speed is 3.1316 m/s. Check that the fall angle is the larger one.

The energy loss

Friction in the bearings, vibration, rubbing of the specimen and air drag all take some energy, and running the machine with no specimen is one way to estimate them. If you know this figure, enter it, and the calculator subtracts it from the energy. If you leave the box empty, no loss is subtracted, and the result is a slight over-estimate of the energy that the specimen absorbed.

Charpy and Izod

The Izod specimen is held as a cantilever at one end [2], and the Charpy specimen is supported at both ends and struck in the middle [1]. The energy calculation is the same for both. The standards include ASTM D256 for Izod testing of plastics [2] and ASTM E23 for notched bar impact testing of metallic materials [1].

US and metric units

In US mode, enter the hammer mass in pounds, the length in inches and any loss in foot-pounds-force; in metric mode, enter kilograms, metres and joules. The angles are always in degrees. The calculator converts to SI, uses g = 9.80665 m/s² and shows the energy in both joules and foot-pounds. The conversion factors are standard values of our own, not from the pages cited.

Reading the result

A high absorbed energy means a tough material under this test, and a low one means brittle behaviour. Absorbed energy also depends on the temperature, the notch shape and the size of the specimen, so only compare results from the same test conditions. The calculator checks the inputs: if the angle of rise is not smaller than the angle of fall, it reports that no energy was absorbed.

Why impact tests matter

Impact tests show how a material behaves under a sudden load, which a slow tensile test cannot reveal. Steels that are tough at room temperature can turn brittle in the cold, and the Charpy test is a common way to see this change [1]. Engineers run the test at several temperatures and compare the absorbed energy. This calculator handles the arithmetic of one test, and the numbers only make sense when the specimen, notch and temperature follow the relevant standard.

Common mistakes

  • Swapping the two angles. The angle of fall is where the hammer starts and the angle of rise is where it ends.
  • Measuring the angles from the horizontal. Both angles are measured from the vertical.
  • Using the length to the pivot's end. Use the length to the strike centre.
  • Ignoring the machine's losses. Run the machine with no specimen to estimate them.

What next

Use this often? Add Impact Test to your Home screen.

Frequently asked questions

What is an impact test calculator?

A tool that finds the energy absorbed by a specimen in a Charpy or Izod pendulum test.

What is the Charpy energy formula?

E = m g S (cos α − cos β) − E_l, or m g (h − h′) from the two heights.

What is the angle of fall and the angle of rise?

The fall angle is where the hammer is released, and the rise angle is where it stops after breaking the specimen.

Why subtract an energy loss?

Friction and air drag take some energy, so the specimen absorbed a little less than the swing lost.

What is the difference between Charpy and Izod?

Charpy supports the specimen at both ends, while Izod holds it as a cantilever.

What went wrong?

We only receive the reason you pick, never what you typed into the tool.

Thanks for your feedback.

More Physics & Science Tools